Building a couple of AR's
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
-
- Advanced Levergunner
- Posts: 4429
- Joined: Wed Sep 12, 2007 12:33 pm
- Location: Wyoming and Arizona
Building a couple of AR's
Was in the PX over at the Marine base today, they had Anderson lowers for 48 bucks so I bought a couple. Have been meaning to do this for some time. This will be my first adventure at this, I have a couple of good CD's detailing all the steps and I have most of the tools already. Thinking I will put together a carbine and a varminter, both .223. Anyone have any sage advice? Thanks, no, I will NOT go over to that AR15 website.
- AJMD429
- Posting leader...
- Posts: 32291
- Joined: Sun Sep 09, 2007 10:03 am
- Location: Hoosierland
- Contact:
Re: Building a couple of AR's
It's pretty easy to get the basics put together. Worst part for me is when the gas-tube holes in a screw-on forend don't align and I have to decide between 'too much torque' or 'too little'. Sometimes I use some Teflon plumbing tape to thicken the shoulder on the barrel assembly that is pushed on by the barrel nut/forend.
You'll of course want to do one in 300 Blk soon, then 50 Beowulf, then 204 Ruger, etc., etc....
The 'AR-15.com' site has lots of good info, but I have more trouble sorting out which 'know-everything' guys there actually know something vs. which ones are just pretending, so I tend to come back to levergunscommunity.com if I want information I can trust...
You'll of course want to do one in 300 Blk soon, then 50 Beowulf, then 204 Ruger, etc., etc....
The 'AR-15.com' site has lots of good info, but I have more trouble sorting out which 'know-everything' guys there actually know something vs. which ones are just pretending, so I tend to come back to levergunscommunity.com if I want information I can trust...
Doctors for Sensible Gun Laws
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.
Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.
Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
Re: Building a couple of AR's
Midweight 1/8 twist in the carbine.
1 in 9 or 1/7 in the varminter depending on your favorite bullet weights. Stiff medium contour barrel, not a bull barrel. Rifle length gas system in the varminter. A GOOD freefloat tube, railed or not (up to you) and a LaRue LT104 for the optic mount.
1 in 9 or 1/7 in the varminter depending on your favorite bullet weights. Stiff medium contour barrel, not a bull barrel. Rifle length gas system in the varminter. A GOOD freefloat tube, railed or not (up to you) and a LaRue LT104 for the optic mount.
- 7.62 Precision
- Senior Levergunner
- Posts: 1836
- Joined: Sat Mar 31, 2012 12:34 am
- Location: Alaska
- Contact:
Re: Building a couple of AR's
The torque range is pretty wide so they will usually align within it. I torque, back it off, torque, back it off, and torque again.AJMD429 wrote:Worst part for me is when the gas-tube holes in a screw-on forend don't align and I have to decide between 'too much torque' or 'too little'. Sometimes I use some Teflon plumbing tape to thicken the shoulder on the barrel assembly that is pushed on by the barrel nut/forend.
Oh and use the correct grease when installing the barrel nut. This is a requirement. Also, if the barrel nut is aluminum, it can weld itself to the upper as you torque it, and it won't move, but it won't be torqued.
On the varmint rifle, don't go over 20" as there is no advantage there. I have some nice 18" match mid weight barrels. Bull barrels are great, if you don't mind the weight, but if you can get the same accuracy from a mid-profile barrel, then why carry the extra weight?
I am avoiding any parts I don't already know to be good right now.
http://www.SHWAT.com
Front Line Holsters • http://www.7-62precision.com • Custom Finishes • http://www.762precision.wordpress.com
Front Line Holsters • http://www.7-62precision.com • Custom Finishes • http://www.762precision.wordpress.com
Re: Building a couple of AR's
I use the same "seating" method you describe here and have never had a problem damaging parts or removing a barrel latter. The use of a good anti-seize grease is something a lot of people seem to forget. I've taken barrels off uppers for people to find the threads on the receiver damaged buy not having been lubed during assembly.7.62 Precision wrote:The torque range is pretty wide so they will usually align within it. I torque, back it off, torque, back it off, and torque again.AJMD429 wrote:Worst part for me is when the gas-tube holes in a screw-on forend don't align and I have to decide between 'too much torque' or 'too little'. Sometimes I use some Teflon plumbing tape to thicken the shoulder on the barrel assembly that is pushed on by the barrel nut/forend.
Oh and use the correct grease when installing the barrel nut. This is a requirement. Also, if the barrel nut is aluminum, it can weld itself to the upper as you torque it, and it won't move, but it won't be torqued.
On the varmint rifle, don't go over 20" as there is no advantage there. I have some nice 18" match mid weight barrels. Bull barrels are great, if you don't mind the weight, but if you can get the same accuracy from a mid-profile barrel, then why carry the extra weight?
I am avoiding any parts I don't already know to be good right now.
I built a really nice 24" varmint AR one time and after running it over a chronograph promptly cut the barrel to 20". I think I gained about 47fps average for 4" of barrel length and weight. Just not worth it.
jnyork, the nice thing about AR's is that you can build a couple of lowers, say one with your choice of a collapsible stock and one with a fixed or heavier adjustable stock, then build and attach uppers to your hearts desire and pretty much take care of any AR type system you can imagine.
Rob
Proud to be Christian American and not ashamed of being white.
May your rifle always shoot straight, your mag never run dry, you always have one more round than you have adversaries, and your good mate always be there to watch your back.
Because I can!
Never grow a wishbone where a backbone ought to be.
May your rifle always shoot straight, your mag never run dry, you always have one more round than you have adversaries, and your good mate always be there to watch your back.
Because I can!
Never grow a wishbone where a backbone ought to be.
Re: Building a couple of AR's
Shoot this putting together an accurate AR is a piece of cake !
I bought the stuff and hand it to my gunsmith buddy and he does the work for me at no cost (part of our trade agreement for doing his internet stuff) !
I bought the stuff and hand it to my gunsmith buddy and he does the work for me at no cost (part of our trade agreement for doing his internet stuff) !
Parkers , Mannlicher Schoenauer’s , 6.5mm's and my family in the Philippines !
- Ysabel Kid
- Moderator
- Posts: 27918
- Joined: Mon Sep 17, 2007 7:10 pm
- Location: South Carolina, USA
- Contact:
Re: Building a couple of AR's
So, at a PX, are they considered an FFL, and do you need to fill out the usual paperwork?jnyork wrote:Was in the PX over at the Marine base today, they had Anderson lowers for 48 bucks so I bought a couple.
- 7.62 Precision
- Senior Levergunner
- Posts: 1836
- Joined: Sat Mar 31, 2012 12:34 am
- Location: Alaska
- Contact:
Re: Building a couple of AR's
What I really hate is the people (and companies) who "bed" the barrel on an AR using epoxy or red locktite.firefuzz wrote: I use the same "seating" method you describe here and have never had a problem damaging parts or removing a barrel latter. The use of a good anti-seize grease is something a lot of people seem to forget. I've taken barrels off uppers for people to find the threads on the receiver damaged buy not having been lubed during assembly.
I just had to take some rifles apart that were built by a manufacturer who did that - the epoxy was between the barrel extension and the upper, on the threads of the barrel nut, between the barrel nut and the barrel, between the gas block and the barrel.
I used every method I knew, but on one of the rifles, I finally had to cut the delta ring and weld spring assembly off and put a big pipe wrench on the barrel nut. In the end, it was easier to replace the upper than deal with the epoxy inside it, plus I was worried that I had stressed it too much taking the barrel off.
While it might make some difference for accuracy, I sure can't shoot well enough to see a difference. I think that "bedding" a barrel on an AR-15 is just a marketing ploy to make people think they are getting a more accurate rifle.
Oh, and the PX has an FFL for each location that firearms are sold.
http://www.SHWAT.com
Front Line Holsters • http://www.7-62precision.com • Custom Finishes • http://www.762precision.wordpress.com
Front Line Holsters • http://www.7-62precision.com • Custom Finishes • http://www.762precision.wordpress.com
Re: Building a couple of AR's
I used this book as a guide when I started building my ARs...
http://www.amazon.com/AR-15-Complete-As ... mbly+Guide
Walt Kuleck and Clint McKee know the AR platform. Check out Fulton Armory.
http://www.amazon.com/AR-15-Complete-As ... mbly+Guide
Walt Kuleck and Clint McKee know the AR platform. Check out Fulton Armory.
Some people just need a sympathetic pat on the head.....with a hammer. Repeatedly.
Re: Building a couple of AR's
They're preying on guys coming from a bolt gun background.7.62 Precision wrote:What I really hate is the people (and companies) who "bed" the barrel on an AR using epoxy or red locktite.firefuzz wrote: I use the same "seating" method you describe here and have never had a problem damaging parts or removing a barrel latter. The use of a good anti-seize grease is something a lot of people seem to forget. I've taken barrels off uppers for people to find the threads on the receiver damaged buy not having been lubed during assembly.
I just had to take some rifles apart that were built by a manufacturer who did that - the epoxy was between the barrel extension and the upper, on the threads of the barrel nut, between the barrel nut and the barrel, between the gas block and the barrel.
I used every method I knew, but on one of the rifles, I finally had to cut the delta ring and weld spring assembly off and put a big pipe wrench on the barrel nut. In the end, it was easier to replace the upper than deal with the epoxy inside it, plus I was worried that I had stressed it too much taking the barrel off.
While it might make some difference for accuracy, I sure can't shoot well enough to see a difference. I think that "bedding" a barrel on an AR-15 is just a marketing ploy to make people think they are getting a more accurate rifle.
Oh, and the PX has an FFL for each location that firearms are sold.
After all, if it's good for a 700 action, it MUST be good for an AR.....yeah...
-
- Advanced Levergunner
- Posts: 4429
- Joined: Wed Sep 12, 2007 12:33 pm
- Location: Wyoming and Arizona
Re: Building a couple of AR's
Ysabel Kid wrote:So, at a PX, are they considered an FFL, and do you need to fill out the usual paperwork?jnyork wrote:Was in the PX over at the Marine base today, they had Anderson lowers for 48 bucks so I bought a couple.
Yes.
-
- Levergunner 3.0
- Posts: 583
- Joined: Wed Apr 25, 2007 8:42 am
Re: Building a couple of AR's
Off of the top of my head, the torque specs are between 35lbs and 80lbs per T.O. Just remember to add a bit of grease to the threads as 7.62 is right in stating that it will fuse itself. Lining up the gas tube can be the hardest part for some along with setting the detent and springs for the hinge pin. There are a few tricks that can be learned. If you need tools, drop me a line. I have just about every AR associated tool you can think of and can ship. There is not any "gun smithing" involved with AR's. It's more along the lines of lincoln logs or leg's. If you send me a PM with your email, I will dig up Uncle Sam's T.O. and send it to you.
Re: Building a couple of AR's
I had a friend of a friend bring me a lower with an M4 type stock on it wanting to change it to an A2 stock. You could see the epoxy in the wrench slots of the locking ring. I asked him why he had done that to which he said the "gunsmith" that put the gun together for him had done it. I actually knew this "gunsmith" so I told him to take the piece back to him for removal and he said he'd already tried, the guy laughed and told him "that stuff ain't never coming off."7.62 Precision wrote:...What I really hate is the people (and companies) who "bed" the barrel on an AR using epoxy or red locktite.
I just had to take some rifles apart that were built by a manufacturer who did that - the epoxy was between the barrel extension and the upper, on the threads of the barrel nut, between the barrel nut and the barrel, between the gas block and the barrel.
So I went with the guy to talk to the "gunsmith" and I asked him why he had epoxied these parts instead of tightening and either using blue locktite or staking it if he was concerned about it loosening. The "gunsmith" said that he didn't have the spanner to tighten the lock ring and besides "his way was better"....tightening the lock ring with a strap wrench after applying this super epoxy. Alarm bells started going off in my head so I asked the "gunsmith" how he installed the barrel lock nut...."same way, I've put together about 20 that way and have never had one come loose." I gave the gun owner my lawyers card standing in front of the "gunsmith" and told him to call me when the gun blew up, if he was able to. I was asked to leave after I told the "gunsmith" what an idiot he was.
How can someone make something so simple be so complicated?
Rob
Proud to be Christian American and not ashamed of being white.
May your rifle always shoot straight, your mag never run dry, you always have one more round than you have adversaries, and your good mate always be there to watch your back.
Because I can!
Never grow a wishbone where a backbone ought to be.
May your rifle always shoot straight, your mag never run dry, you always have one more round than you have adversaries, and your good mate always be there to watch your back.
Because I can!
Never grow a wishbone where a backbone ought to be.
- Griff
- Posting leader...
- Posts: 20877
- Joined: Sat Mar 31, 2007 4:56 pm
- Location: OH MY GAWD they installed a STOP light!!!
Re: Building a couple of AR's
Man, you guys got me worried... the assembled upper I bought has a Hogue forend on it... I wanted to take it of to drill & tap it for a short section of rail... Marked where the holes needed to be... but now can't figure how to remove it... guess I better ask Hogue...
Griff,
SASS/CMSA #93
NRA Patron
GUSA #93
There is a fine line between hobby & obsession!
AND... I'm over it!!
No I ain't ready, but let's do it anyway!
SASS/CMSA #93
NRA Patron
GUSA #93
There is a fine line between hobby & obsession!
AND... I'm over it!!
No I ain't ready, but let's do it anyway!
- vancelw
- Advanced Levergunner
- Posts: 3934
- Joined: Mon Sep 28, 2009 1:56 pm
- Location: 90% NE Texas and 10% SE Montana
Re: Building a couple of AR's
That's the main reason I am seriously considering going to gunsmithing school now that I'm retired. Of the dozen or so "gunsmiths" around here, there is not one I trust. We have so many AR assemblers around here that I would never buy a used one without tearing it down first. Especially after reading this thread.firefuzz wrote:
How can someone make something so simple be so complicated?
Rob
It also amazes me how many people expect a rifle that has been bore-sighted to be dead-on at 300 yards (or any range)
"Make yourself an honest man, and then you may be sure that there is one less scoundrel in the world." - Thomas Carlyle
Re: Building a couple of AR's
I just finished building one and am in the process of building another...AR's, I'm discovering, are fun to put together... :)
Last edited by 1894c on Mon Jan 12, 2015 12:09 am, edited 1 time in total.
Re: Building a couple of AR's
They are very addicting. Back in the day even the worst one I ever put together, with an already wore out target barrel, would still shoot 1 1/2 MOA with iron sights, when I could see them.1892 wrote:I just finished building one and am in the process of building another...AR's, I discovering, are fun to put together...
Buton
Re: Building a couple of AR's
Very fun and easy to do yourself. There a lot of quality You Tube videos out there to show you how. The easy button is buy this DVD:
http://www.amazon.com/Building-Your-AR- ... B004ZZDYDG
http://www.amazon.com/Building-Your-AR- ... B004ZZDYDG
Snoopin & Shootin,
Dean
Dean
Re: Building a couple of AR's
Also I would advise buying all your parts from quality manufactureres. A bunch of bargain basement parts will make a bargain basement AR.
Snoopin & Shootin,
Dean
Dean
Re: Building a couple of AR's
I agree with what you're saying here, but don't swing too far the other way. A person can build an accurate, serviceable AR right now for less than $600. It may not have all the bells and whistles, but it will be reliable and accurate. Do a little research and buy quality, not necessarily big name parts. The really nice thing about AR's is that they are easy to upgrade as you cash flow dictates.DiamondD wrote:Also I would advise buying all your parts from quality manufactureres. A bunch of bargain basement parts will make a bargain basement AR.
Rob
Proud to be Christian American and not ashamed of being white.
May your rifle always shoot straight, your mag never run dry, you always have one more round than you have adversaries, and your good mate always be there to watch your back.
Because I can!
Never grow a wishbone where a backbone ought to be.
May your rifle always shoot straight, your mag never run dry, you always have one more round than you have adversaries, and your good mate always be there to watch your back.
Because I can!
Never grow a wishbone where a backbone ought to be.