45-70 or .348
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
45-70 or .348
So, I'm looking at purchasing either a browning carbine 1886 in 45-70 or a Winchester 71 in .348. Both are in excellent shape. Negatives for both that m looking for are neither is tapped for receiver sights. Hate to say it but I would have to have that done as the sights just don't do it for me anymore.
Your thoughts? Which one?
Your thoughts? Which one?
Mike Johnson,
"Only those who will risk going too far, can possibly find out how far one can go." T.S. Eliot
"Only those who will risk going too far, can possibly find out how far one can go." T.S. Eliot
-
- Advanced Levergunner
- Posts: 4296
- Joined: Wed Sep 15, 2010 12:57 pm
- Location: Vinita, I.T.
Re: 45-70 or .348
I have the Browning 86 carbine. Mine had the receiver sight on when I bought it so don't know if it had to be drilled and tapped or not. I think the 45-70 is a very adaptable caliber. Many different bullets and loadings allow you to do almost anything with it.
I wouldn't hesitate to drill and tap a Browning as I doubt there'll ever be much collector interest in them that will make it less valuable. Heck, mine's been shortened to a 19 inch barrel. Sure makes it handy.
I wouldn't hesitate to drill and tap a Browning as I doubt there'll ever be much collector interest in them that will make it less valuable. Heck, mine's been shortened to a 19 inch barrel. Sure makes it handy.
M. M. Wright, Sheriff, Green county Arkansas (1860)
Currently living my eternal life.
NRA Life
SASS
ITSASS
Currently living my eternal life.
NRA Life
SASS
ITSASS
Re: 45-70 or .348
Mike, is there anything the 348 can do that the 45/70 cannot?
Or vice-versa?
Which has the better selection of bullets and loads?
Which one has the "it" factor for you?
A lot of folks really like the 348.
If throw-weight is a consideration, the choice narrows rapidly . . .
The Brownings are fine firearms and you will appreciate either one.
Or vice-versa?
Which has the better selection of bullets and loads?
Which one has the "it" factor for you?
A lot of folks really like the 348.
If throw-weight is a consideration, the choice narrows rapidly . . .
The Brownings are fine firearms and you will appreciate either one.
Re: 45-70 or .348
I'd go for the .348.....I had a JapChester 1886 EL, and found it to be cumbersome, and picky on OAL to a point that I had to load for it separately. (Loads that chambered in my Marlin would not in the 1886.) Maybe the Browning iteration is different.
The Rotten Fruit Always Hits The Ground First
Proud Life Member Of:
NRA
Second Amendment Foundation
Citizens Committee For The Right To Keep And Bear Arms
DAV
Proud Life Member Of:
NRA
Second Amendment Foundation
Citizens Committee For The Right To Keep And Bear Arms
DAV
Re: 45-70 or .348
There isn't ANY way shape or form that I'd d&t an excellent model 71 Winchester. Those little holes will cost you $500 a piece in value. I know 71's are hard to find, but the later ones use a Lyman side mounted peep sight that uses the factory holes, if that would do you. Otherwise I'd find a 95 Marlin in 45-70 and put a scope on that, if you're looking for optics.rjohns94 wrote:So, I'm looking at purchasing either a browning carbine 1886 in 45-70 or a Winchester 71 in .348. Both are in excellent shape. Negatives for both that m looking for are neither is tapped for receiver sights. Hate to say it but I would have to have that done as the sights just don't do it for me anymore.
Your thoughts? Which one?
I used a four digit Winchester 71 deluxe to hunt deer for many years, and I really like the .348 cartridge, so I can see why you'd want to go that way, but I just cringe at drilling those holes....
-
- Levergunner 3.0
- Posts: 933
- Joined: Wed Jan 21, 2009 1:08 am
- Location: Salmon Creek, SW Washington
Re: 45-70 or .348
Owning both, my vote is tossed in the ring for the 71. Mine will shot under 3" at 200 yards with the bolt mounted peep. More power than most of us will ever need in this lifetime.
"Yes, we did produce a near-perfect republic. But will they keep it? Or will they, in the enjoyment of plenty, lose the memory of freedom? Material abundance without character is the path of destruction." - Thomas Jefferson
- vancelw
- Advanced Levergunner
- Posts: 3950
- Joined: Mon Sep 28, 2009 1:56 pm
- Location: 90% NE Texas and 10% SE Montana
Re: 45-70 or .348
Are you sure the Browning 1886 is not D&T'd for receiver sights? Every one I have ever seen was.
That being said, I'd buy the Winchester 71.
Why? Because I already have a Browning 1886 SRC and 71 (They both were factory drilled for receiver sights and sport them)
If I was going to put a peep on a Winchester 71 I would try to find a bolt mounted one, like the deluxe version had.
That being said, I'd buy the Winchester 71.
Why? Because I already have a Browning 1886 SRC and 71 (They both were factory drilled for receiver sights and sport them)
If I was going to put a peep on a Winchester 71 I would try to find a bolt mounted one, like the deluxe version had.
"Make yourself an honest man, and then you may be sure that there is one less scoundrel in the world." - Thomas Carlyle
Re: 45-70 or .348
BUY BOTH! Have the Browning 348 carbine and the Browning 86 SRC. Pre lawyer guns. Craftmanship and shoot ability are excellent. They don't build them like this no more.
Re: 45-70 or .348
If my memory serves me right, you also have to have the bolt to go with that original bolt mounted peep sight. I can't remember just how that is attached, but I think there are a couple of grooves machined in the top of the bolt for the sight, and a cross pin to hold it in. Correct me if I'm off base about that.vancelw wrote:Are you sure the Browning 1886 is not D&T'd for receiver sights? Every one I have ever seen was.
That being said, I'd buy the Winchester 71.
Why? Because I already have a Browning 1886 SRC and 71 (They both were factory drilled for receiver sights and sport them)
If I was going to put a peep on a Winchester 71 I would try to find a bolt mounted one, like the deluxe version had.
When we're talking about "receiver sights" do you mean 'tang' sights or mounted on the side of the receiver? On my 71's the long tang one has no holes in either the tang or receiver. On the 1956 version there's only the receiver mounted sight and no holes for a tang sight. On the Browning .348 made in 84, it is the same as the 1956, model 71, screws for the side mount peep and no holes for the tang sight. That should narrow down your search.
And as TMAN said, buy both. Check out the fit of the Browning in the bottom picture.....outstanding.
Irv
- vancelw
- Advanced Levergunner
- Posts: 3950
- Joined: Mon Sep 28, 2009 1:56 pm
- Location: 90% NE Texas and 10% SE Montana
Re: 45-70 or .348
Don't know if you were talking to me or Mike, but receiver sights are mounted on the receiver and tang sights are mounted on the tang. Both are forms of peep sights. The Brownings I've seen all are D&T'd for receiver sights. I've got Williams on most of mine. Tang sights are inherently more accurate with their longer sight radius, but I don't like them as well in hunting situations.Daisyman wrote:vancelw wrote:Are you sure the Browning 1886 is not D&T'd for receiver sights? Every one I have ever seen was.
Why? Because I already have a Browning 1886 SRC and Browning 71 (They both were factory drilled for receiver sights and sport them)
When we're talking about "receiver sights" do you mean 'tang' sights or mounted on the side of the receiver? On my 71's the long tang one has no holes in either the tang or receiver.
Irv
I'm not sure how that bolt-mounted peep fit on the Win 71s. It would be hard to find an original of either. If I had a "shooter" instead of a collector I might put a Skinner on it. I don't own any non-shooters
"Make yourself an honest man, and then you may be sure that there is one less scoundrel in the world." - Thomas Carlyle
Re: 45-70 or .348
I've had two of the Browning 86's, neither was D&T'ed from the factory, and none I've seen were. The Browning 71's were, but not 86's. I believe the Miroku/Winchester 86's were D&T'ed from the factory though.
Its fairly simple to D&T the Browning 86's, but go slow and back the tap out a lot to keep the chips clear. Breaking a tap isnt fun.
I've been a long time fan of the 45-70, and they are quite versatile, but have come to appreciate the 348 quite a lot.
Curious, that an 86 would be finicky about OAL compared to a Marlin. The 86 action can handle much longer cartridges than the Marlins. 45-90's arent a problem so long as the loading gate path is clearanced.
Its fairly simple to D&T the Browning 86's, but go slow and back the tap out a lot to keep the chips clear. Breaking a tap isnt fun.
I've been a long time fan of the 45-70, and they are quite versatile, but have come to appreciate the 348 quite a lot.
Curious, that an 86 would be finicky about OAL compared to a Marlin. The 86 action can handle much longer cartridges than the Marlins. 45-90's arent a problem so long as the loading gate path is clearanced.
"Far better it is to dare mighty things, to win glorious triumphs even though checkered by failure, than to rank with those poor spirits who neither enjoy nor suffer much because they live in the gray twilight that knows neither victory nor defeat." -Theodore Roosevelt-
Isnt it amazing how many people post without reading the thread?
Isnt it amazing how many people post without reading the thread?
Re: 45-70 or .348
my miroku/win 1886TD is not drilled and tapped. 2000-2001 year.
Re: 45-70 or .348
Mike,
I'm not sure if I understand the choice you are faced with. If I'm reading correctly...you are trying to decide between a Browning COPY of an 1886 Winchester, and a WINCHESTER M-71.
That's a no brainer...the Winchester is a true classic. The Browning...while it might be a decent rifle is, well...a COPY of a true classic.
OTOH: if BOTH of the rifles you're looking at are copies...It comes back to getting some kind of sighting system you can use, and since we're not talking about original Winchesters...drill away brother...and ENJOY..!!
As to the issue with COL mentioned...I believe the limitation some have observed in those Browning carbines is related to the throat of the chamber. They aren't throated for quite the wide variety of bullets the 45/70 is rightfully famous for, and some folks might want to use.
I'm not sure if I understand the choice you are faced with. If I'm reading correctly...you are trying to decide between a Browning COPY of an 1886 Winchester, and a WINCHESTER M-71.
That's a no brainer...the Winchester is a true classic. The Browning...while it might be a decent rifle is, well...a COPY of a true classic.
OTOH: if BOTH of the rifles you're looking at are copies...It comes back to getting some kind of sighting system you can use, and since we're not talking about original Winchesters...drill away brother...and ENJOY..!!
As to the issue with COL mentioned...I believe the limitation some have observed in those Browning carbines is related to the throat of the chamber. They aren't throated for quite the wide variety of bullets the 45/70 is rightfully famous for, and some folks might want to use.
-
- Senior Levergunner
- Posts: 1263
- Joined: Mon Dec 17, 2007 7:57 pm
Re: 45-70 or .348
How far are you going to be shooting? A 45/70 becomes a challenge for holdover for me at anything past 200 yards. The .348 I could shoot 250 or maybe even 300 yards. If its for inside 150 yards, flip a coin. A really nice problem to have!
Re: 45-70 or .348
Pics of the 1886 and the model 71. Price is an issue as the Winchester is a bit more than the browning. Note, not drill and tapped. 71 on top, 1886 on bottom, top picture.
You do not have the required permissions to view the files attached to this post.
Mike Johnson,
"Only those who will risk going too far, can possibly find out how far one can go." T.S. Eliot
"Only those who will risk going too far, can possibly find out how far one can go." T.S. Eliot
Re: 45-70 or .348
.
The bolt peep sight, found on some New Haven Winchester Model(s) 64 & 71's, is fitted into a multi-machined recess in the rear half of the bolt top.
IIRC, Montana Vintage Arms once offered a bolt peep ($250) AND would also machine your bolt for the sight (+ $250).
AFAIK, there's no way a New Haven Winchester 71 can be documented as to whether or not it left the factory with the receiver sight prep (2 D/T'd & plugged holes).
Soooooo (my $0.02), I would take the gennie (N.H.Winchester 71) over the clone (Browning whatever) in a N.Y.Minute, then upgrade the Model 71 to factory specs with the receiver sight prep.
(YMMV)
.
The bolt peep sight, found on some New Haven Winchester Model(s) 64 & 71's, is fitted into a multi-machined recess in the rear half of the bolt top.
IIRC, Montana Vintage Arms once offered a bolt peep ($250) AND would also machine your bolt for the sight (+ $250).
AFAIK, there's no way a New Haven Winchester 71 can be documented as to whether or not it left the factory with the receiver sight prep (2 D/T'd & plugged holes).
Soooooo (my $0.02), I would take the gennie (N.H.Winchester 71) over the clone (Browning whatever) in a N.Y.Minute, then upgrade the Model 71 to factory specs with the receiver sight prep.
(YMMV)
.
Re: 45-70 or .348
Ah, that makes sense. Getting it throated isnt a big issue if one wanted to shoot loads that were fatter up front.guido4198 wrote:
As to the issue with COL mentioned...I believe the limitation some have observed in those Browning carbines is related to the throat of the chamber. They aren't throated for quite the wide variety of bullets the 45/70 is rightfully famous for, and some folks might want to use.
I think I'd agree with that idea. Get good measurements on location and drill the 71. They look great with the Lyman 56 sights.Pete44ru wrote: AFAIK, there's no way a New Haven Winchester 71 can be documented as to whether or not it left the factory with the receiver sight prep (2 D/T'd & plugged holes).
Soooooo (my $0.02), I would take the gennie (N.H.Winchester 71) over the clone (Browning whatever) in a N.Y.Minute, then upgrade the Model 71 to factory specs with the receiver sight prep.
(YMMV)
"Far better it is to dare mighty things, to win glorious triumphs even though checkered by failure, than to rank with those poor spirits who neither enjoy nor suffer much because they live in the gray twilight that knows neither victory nor defeat." -Theodore Roosevelt-
Isnt it amazing how many people post without reading the thread?
Isnt it amazing how many people post without reading the thread?
- vancelw
- Advanced Levergunner
- Posts: 3950
- Joined: Mon Sep 28, 2009 1:56 pm
- Location: 90% NE Texas and 10% SE Montana
Re: 45-70 or .348
I think I remember seeing that, too. Ouchie.Pete44ru wrote:
IIRC, Montana Vintage Arms once offered a bolt peep ($250) AND would also machine your bolt for the sight (+ $250).
I would love to have a real Winchester 71, and if I do get one, I will shoot the snot out of it.Pete44ru wrote: Soooooo (my $0.02), I would take the gennie (N.H.Winchester 71) over the clone (Browning whatever) in a N.Y.Minute, then upgrade the Model 71 to factory specs with the receiver sight prep.
(YMMV)
"Make yourself an honest man, and then you may be sure that there is one less scoundrel in the world." - Thomas Carlyle
Re: 45-70 or .348
[quote="Pete44ru"].
The bolt peep sight, found on some New Haven Winchester Model(s) 64 & 71's, is fitted into a multi-machined recess in the rear half of the bolt top.
AFAIK, there's no way a New Haven Winchester 71 can be documented as to whether or not it left the factory with the receiver sight prep (2 D/T'd & plugged holes).
You are correct on the bolt peep. I have a 65 .218 Bee and it is that way.
As for the D&T on the receiver, the later 71's were definitely available for the Lyman 56 peep. The picture of mine above is definitely original and there are many examples of them out there.
Irv
The bolt peep sight, found on some New Haven Winchester Model(s) 64 & 71's, is fitted into a multi-machined recess in the rear half of the bolt top.
AFAIK, there's no way a New Haven Winchester 71 can be documented as to whether or not it left the factory with the receiver sight prep (2 D/T'd & plugged holes).
You are correct on the bolt peep. I have a 65 .218 Bee and it is that way.
As for the D&T on the receiver, the later 71's were definitely available for the Lyman 56 peep. The picture of mine above is definitely original and there are many examples of them out there.
Irv
Re: 45-70 or .348
That is a beautiful 71. I don't know what they are asking for it and don't want to know, but unless it's a really good buy, why not find a later 71 like mine that has the side mounted peep already on it.rjohns94 wrote:Pics of the 1886 and the model 71. Price is an issue as the Winchester is a bit more than the browning. Note, not drill and tapped. 71 on top, 1886 on bottom, top picture.
That way the original is preserved and you get what you want. It's really hard to put that little bit of drilled metal back in those holes, and for what you lose in value you could have the one you want. There's almost always one on gunbroker that's a shooter. IMHO
Irv
- Griff
- Posting leader...
- Posts: 21016
- Joined: Sat Mar 31, 2007 4:56 pm
- Location: OH MY GAWD they installed a STOP light!!!
Re: 45-70 or .348
.348. Didn't you already have a 1886 carbine and found it lacking?
Griff,
SASS/CMSA #93
NRA Patron
GUSA #93
There is a fine line between hobby & obsession!
AND... I'm over it!!
No I ain't ready, but let's do it anyway!
SASS/CMSA #93
NRA Patron
GUSA #93
There is a fine line between hobby & obsession!
AND... I'm over it!!
No I ain't ready, but let's do it anyway!
Re: 45-70 or .348
.
Or, combine the two....................
I've seen a pretty neat custom (Browning) Model 71, that was converted to .45-70, with a full-length magazine.
IDK who the custom gunsmith was (Ed Noonan ?), but now, Cimmaron (Italy) makes a .45-70 Model 71 clone.
.
Or, combine the two....................
I've seen a pretty neat custom (Browning) Model 71, that was converted to .45-70, with a full-length magazine.
IDK who the custom gunsmith was (Ed Noonan ?), but now, Cimmaron (Italy) makes a .45-70 Model 71 clone.
.
Re: 45-70 or .348
I've seen a couple of original 71s rebarreled to 45-70, I think it wasnt uncommon in the past. Funny though, my interest lies in the opposite direction. I'd like to have what would basically be an 86 short rifle in 348. 22" light round barrel, full mag, straight grip, shotgun butt, checkered nice grade wood, sling mounts, Lyman 56 sight, tiny ramp like the 86 XL rifles had. Maybe some very low profile scope bases on the barrel.Pete44ru wrote:.
Or, combine the two....................
I've seen a pretty neat custom (Browning) Model 71, that was converted to .45-70, with a full-length magazine.
"Far better it is to dare mighty things, to win glorious triumphs even though checkered by failure, than to rank with those poor spirits who neither enjoy nor suffer much because they live in the gray twilight that knows neither victory nor defeat." -Theodore Roosevelt-
Isnt it amazing how many people post without reading the thread?
Isnt it amazing how many people post without reading the thread?
Re: 45-70 or .348
Get the 71 its is the better hunting rifle Ive found that the mdl 64 and 71 shoulder better for quick shots on game than any other rifles Ive tried there might be a third one a savage 99 something about the stock and pistol grip makes for a excellent hunting rifle. danny
Re: 45-70 or .348
Griff I gave it to my brother for a birthday presentGriff wrote:.348. Didn't you already have a 1886 carbine and found it lacking?
Mike Johnson,
"Only those who will risk going too far, can possibly find out how far one can go." T.S. Eliot
"Only those who will risk going too far, can possibly find out how far one can go." T.S. Eliot
- Griff
- Posting leader...
- Posts: 21016
- Joined: Sat Mar 31, 2007 4:56 pm
- Location: OH MY GAWD they installed a STOP light!!!
Re: 45-70 or .348
Couldn't remember... not an unusual circumstance. If I ever got rid of my 1886, I might want to try something else... like the mdl 71. But, my 1886 ain't goin' anywhere. I really happen to like the versatility of the .45-70... but am impressed by the ballistics of the .348 when compared to the old 45Gov't.rjohns94 wrote:Griff I gave it to my brother for a birthday presentGriff wrote:.348. Didn't you already have a 1886 carbine and found it lacking?
Griff,
SASS/CMSA #93
NRA Patron
GUSA #93
There is a fine line between hobby & obsession!
AND... I'm over it!!
No I ain't ready, but let's do it anyway!
SASS/CMSA #93
NRA Patron
GUSA #93
There is a fine line between hobby & obsession!
AND... I'm over it!!
No I ain't ready, but let's do it anyway!