American gun company New Yorker

[fordwannabe]

The collection of knowledge here amazes me most of the time so I am gonna ask a shotgun question. Does anybody know if the American Gun Company New Yorker used the same size frame for the 28 gauge and the .410? Thanks.

[GunnyMack]

Now that's a good question... I've not seen a small gauge one.

[fordwannabe]

I’d show you a picture but I forgot it at my buddy’s gunshop yesterday. There were two on guns America that showed in a search.

[GunnyMack]

I would think they probably used a 20 ga frame. That's been the normal for a long time.

[fordwannabe]

Thanks Gunny. Seems small for a twenty that was the reason for the OPand I need a stock for it.

[GunnyMack]

Tom I finally looked up the American Gun Company, also know by Crescent Arms. Like I said I've never seen a small gauge one. I doubt a company like this would have scaled the frames for 410/28, be my guess it's a 20ga frame.

Now if it was a Fox Sterlingworth I got a semi inlet in the basement. I have no idea where I got it or when!!

[fordwannabe]

Is for the hammer fox Sterlingworth or the hammerless?

[GunnyMack]

That's a good question, it's just a semi inlet . I'll try to remember to post a rew pics later.

Edit- now that my brain fog has lifted after a good dump my mind is ready for action!

Tom it's a hammerless stock. I'll post pics.

[GunnyMack]

Fox stock pics

20190129_173200-600x800.jpg

20190129_173217-600x800.jpg

20190129_173232-600x800.jpg

Tom if you are interested let me know!

[fordwannabe]

Now I gotta look and see y’all f I need the hammer or hammered stock don’t remember.

[6pt-sika]

I’ve got a Crescent Arms 410 and we’ve had three of them in the shop . I would say they’re smaller then a Crescent 20 but I’ve never seen or atleast noticed a Crescent 20 .

[6pt-sika]

Is for the hammer fox Sterlingworth or the hammerless?

I could be wrong ( but I doubt it on this) AH Fox never made a hammer gun of any kind be it a Sterlingworth or a graded Fox .

[fordwannabe]

Well there ya go must be a hammerless.
Thanks for the reply on the crescent also. Now where do I get a stock for it? Don’t care about originality so much as the locks have been chrome plated and the barrels have been cut A LOT.
Hate to use such blasphemous terms but I might be better to part it out at this point. Dunno?

[GunnyMack]

Time to start trolling the auction sites, gun shows and the like. Ya might get lucky, I did when I found a bolt for my little Winchester single shot 22, cost me more than a C note though!

[fordwannabe]

Oaks gun show is in February. If I have recovered financially from the Sixgun deal. I will be on the lookout or there is a guy from Empire gun parts that I have done business with in the past and see what parts he’ll trade me for it. I have a mossberg 46 to part out also.

[GunnyMack]

There ya go!
I checked GPC- nope, Jack First- nope( I knew better) .
Maybe there is something close that is available and just glass it in...?

[fordwannabe]

Yeah I checked GPC but nothing didn’t check JF so thank you. Didn’t check Boyd’s either. Not a huge priority just on the list of gotta deal with it. Thanks Gunny. See you at Oaks??????

[GunnyMack]

Maybe but I doubt it... still bird hunting on weekends so unless it's raining I wont make the show. The girls have to earn their kibble.
Heck I dont even know when it is!

[fordwannabe]

February 9,10
0900-1800

[6pt-sika]

If you’re so inclined go to the Forks of Delaware Collectors show in Easton PA and or the Maryland Collectors Association Show in Towson MD you might luck up on a stocknor a lead there . https://www.google.com/amp/s/gunshowtra ... -show/amp/. http://www.baltimoreshow.com/

[fordwannabe]

Thank you.

[Sixgun]

Gunny...either your socks are mismatched or one is pulled up further than the other. There! I hopes this helps with Tom's post.--6