Campfire reloading-Pics
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
-
- Levergunner 3.0
- Posts: 559
- Joined: Thu Sep 06, 2007 7:53 pm
- Location: Surrey, England
Campfire reloading-Pics
Had a monster casting session over the holidays and while clearing up I came upon this Ideal combination tool in 38-40.
I bought it when I got my Winchester 1873 but had forgotten all about it. Don't how old it is but the patent date is 1884. Apart from the decapper plug being missing, as usual, it seemed to be in working order so I thought I would try some old-time reloading.
Front to back: bullet sizer die, primer tool, decapper/bullet seater/crimper, mould.
Buffalo chips not being common on the grasslands of southern England, I settled on charcoal for my lead smelting, using a cast iron lead pot and a ladle made from an old spoon. Bullets cast at 0.404 diameter with an average weight of 167.4grains and a standard deviation of 0.14 grains. I hand lubed them with mutton tallow and passed them through the sizer die. They came out at .401
Here they are on the left, compared to the 187 grain Big-Lube bullets that are the normal fodder for my1873 - it has a pitted bore that fouls up with BP in about 3 shots but it shoots really well with a Big-Lube on top of 35 grains of 777.
The mould halves do not fit too well so there is a flash on the side of the bullet thats easy to get off. More serious was some slight damage to the edges of the mould that caused rough edges to the base of the bullet, which I thought might lead to gas cutting.Also I found that the pin that pushes the bullet through the sizer die makes a small off-center dimple in the base of the bullet - not conducive to good accuracy.
I used Starline cases, fireformed in my 1873. I flared the case mouth on the outside taper of the seater die, added 35grains of FFFG from a dipper, slipped it into the seater die and squeezed the handles shut. The result was not half bad although the crimp was very light and could not be increased as far as I could see.
Here they are ready to go, with my standard Big-Lube load in the background.
Went off to the range this morning. Temperature 30F, wind gusting to 20mph, 3in of old snow on the ground.
Much as I would like to report a happy ending it was not to be...........
The first shot went where I expected but from then on it was all downhill. With Big-Lubes and 777 my old 1873 shoots 1.5 - 2in groups at 50 metres but then those rounds are loaded on a Rockchucker using RCBS dies and a factory crimp die, also weighed charges and batched bullets. Maybe I was expecting too much for a 120 year old gun and tool?
Not to worry though, I have a similar tool for my 40-65 Winchester 1886 so will give that a go when the weather improves.
Perry Owens
I bought it when I got my Winchester 1873 but had forgotten all about it. Don't how old it is but the patent date is 1884. Apart from the decapper plug being missing, as usual, it seemed to be in working order so I thought I would try some old-time reloading.
Front to back: bullet sizer die, primer tool, decapper/bullet seater/crimper, mould.
Buffalo chips not being common on the grasslands of southern England, I settled on charcoal for my lead smelting, using a cast iron lead pot and a ladle made from an old spoon. Bullets cast at 0.404 diameter with an average weight of 167.4grains and a standard deviation of 0.14 grains. I hand lubed them with mutton tallow and passed them through the sizer die. They came out at .401
Here they are on the left, compared to the 187 grain Big-Lube bullets that are the normal fodder for my1873 - it has a pitted bore that fouls up with BP in about 3 shots but it shoots really well with a Big-Lube on top of 35 grains of 777.
The mould halves do not fit too well so there is a flash on the side of the bullet thats easy to get off. More serious was some slight damage to the edges of the mould that caused rough edges to the base of the bullet, which I thought might lead to gas cutting.Also I found that the pin that pushes the bullet through the sizer die makes a small off-center dimple in the base of the bullet - not conducive to good accuracy.
I used Starline cases, fireformed in my 1873. I flared the case mouth on the outside taper of the seater die, added 35grains of FFFG from a dipper, slipped it into the seater die and squeezed the handles shut. The result was not half bad although the crimp was very light and could not be increased as far as I could see.
Here they are ready to go, with my standard Big-Lube load in the background.
Went off to the range this morning. Temperature 30F, wind gusting to 20mph, 3in of old snow on the ground.
Much as I would like to report a happy ending it was not to be...........
The first shot went where I expected but from then on it was all downhill. With Big-Lubes and 777 my old 1873 shoots 1.5 - 2in groups at 50 metres but then those rounds are loaded on a Rockchucker using RCBS dies and a factory crimp die, also weighed charges and batched bullets. Maybe I was expecting too much for a 120 year old gun and tool?
Not to worry though, I have a similar tool for my 40-65 Winchester 1886 so will give that a go when the weather improves.
Perry Owens
"Always carry a firearm east of Aldgate Watson."
- Old Savage
- Posting leader...
- Posts: 16787
- Joined: Mon Sep 03, 2007 3:43 pm
- Location: Southern California
Re: Campfire reloading-Pics
Impressive.
- kimwcook
- Advanced Levergunner
- Posts: 7978
- Joined: Tue Sep 04, 2007 10:01 pm
- Location: Soap Lake, WA., U.S.A.
Re: Campfire reloading-Pics
Good show. Really appreciated that. Seems like your tool has seen better days (tighter dimensions). Can't wait for the second one.
Old Law Dawg
Re: Campfire reloading-Pics
Thats really impressive Perry, thanks for sharing that.
I feel it was a success really when considering the tool. It would of still put a rabbit in the pot for you (or other)
Nath.
I feel it was a success really when considering the tool. It would of still put a rabbit in the pot for you (or other)
Nath.
Psalm ch8.
Because I wish I could!
Because I wish I could!
Re: Campfire reloading-Pics
I dont know with the wind being as you say and the fact that you are using a new load I would say not to bad. I think you could can fine tune that load and have it shoot well. Perhaps a grease cookie or card wad will shrink that group up for ya.
Jeremy
GySgt USMC Ret
To err is human, To forgive is devine, Neither of which is Marine Corps policy
Semper Fidelis
GySgt USMC Ret
To err is human, To forgive is devine, Neither of which is Marine Corps policy
Semper Fidelis
-
- Senior Levergunner
- Posts: 1244
- Joined: Mon Sep 03, 2007 3:15 pm
- Location: West Michigan
- Contact:
Re: Campfire reloading-Pics
What JReed said.JReed wrote:Perhaps a grease cookie or card wad will shrink that group up for ya.
I'm not a BPCR shooter by any means but I would certainly give a cookie a try before moving on.
Re: Campfire reloading-Pics
Looking at the targ again it is saying something about how succesive shots have walked, means something but I'm not sure what hmmmm!
Nath.
Nath.
Psalm ch8.
Because I wish I could!
Because I wish I could!
Re: Campfire reloading-Pics
I certainly wouldn't be disappointed with that group. Yes, there is room for improvement but that's not bad for your first try with the old tools. A little experimenting is in order I think.
NRA Life Member
Re: Campfire reloading-Pics
As a newbie levergunner gaining interest in reloading, I'm intriqued by the process of loading with simple tools (though I'm still looking at more modern techniques). With that preface, here are my dumb newbie questions:
1 - can this be done in .30-30?
2 - are these tools available in this modern era?
3 - if yes to either above, where can I obtain these tools?
Thanks for posting this Perry.
1 - can this be done in .30-30?
2 - are these tools available in this modern era?
3 - if yes to either above, where can I obtain these tools?
Thanks for posting this Perry.
"Quando Omni Flunkus Moritati"
-
- Levergunner 3.0
- Posts: 559
- Joined: Thu Sep 06, 2007 7:53 pm
- Location: Surrey, England
Re: Campfire reloading-Pics
Dutch,
The modern equivalent is the Lyman 310 tool. You can get it in 30-30 from Buffalo Arms and many others
http://www.buffaloarms.com/browse.cfm/4,1780.html
They are not quite the same as the old tools as they use detachable dies but they work really well. I don't think you can get one with an integral bullet mould though.
Old reloading tools are still quite common and not overly expensive. They make a neat accessory for an old gun.
Perry Owens
The modern equivalent is the Lyman 310 tool. You can get it in 30-30 from Buffalo Arms and many others
http://www.buffaloarms.com/browse.cfm/4,1780.html
They are not quite the same as the old tools as they use detachable dies but they work really well. I don't think you can get one with an integral bullet mould though.
Old reloading tools are still quite common and not overly expensive. They make a neat accessory for an old gun.
Perry Owens
"Always carry a firearm east of Aldgate Watson."
Re: Campfire reloading-Pics
Thanks Perry. That link gives me a starting point.
edit: ordered the 310 Handles and .30-30 dies
edit: ordered the 310 Handles and .30-30 dies
"Quando Omni Flunkus Moritati"
Re: Campfire reloading-Pics
I would make a couple suggestions for the next batch.
Have you slugged the bore of the rifle to see what the exact groove diameter is?
Try not sizing the bullets, and see if that helps, also, how hard is the lead alloy? With black, it should be fairly soft. The factory rounds from back in the day used swaged lead bullets, very soft.
I believe Elmer Keith wrote of the sizing hole in the Ideal tools rarely being round.
Have you slugged the bore of the rifle to see what the exact groove diameter is?
Try not sizing the bullets, and see if that helps, also, how hard is the lead alloy? With black, it should be fairly soft. The factory rounds from back in the day used swaged lead bullets, very soft.
I believe Elmer Keith wrote of the sizing hole in the Ideal tools rarely being round.
"Far better it is to dare mighty things, to win glorious triumphs even though checkered by failure, than to rank with those poor spirits who neither enjoy nor suffer much because they live in the gray twilight that knows neither victory nor defeat." -Theodore Roosevelt-
Isnt it amazing how many people post without reading the thread?
Isnt it amazing how many people post without reading the thread?
-
- Levergunner 3.0
- Posts: 559
- Joined: Thu Sep 06, 2007 7:53 pm
- Location: Surrey, England
Re: Campfire reloading-Pics
Thanks everyone for the suggestions. I use wads, scrubbers and grease cookies in all my other black powder rifles but for this experiment I did not want to use anything that might not be available to the average farmer or ranchhand of the 1880s. I may try to tidy the mould up a bit or at least use a card wad to protect the bullet base.
Malamute - I have not slugged the bore but the rifle performs well with modern .401 bullets. I used pure lead for casting but I will try unsized bullets as you suggest.
Perry Owens
Malamute - I have not slugged the bore but the rifle performs well with modern .401 bullets. I used pure lead for casting but I will try unsized bullets as you suggest.
Perry Owens
"Always carry a firearm east of Aldgate Watson."
Re: Campfire reloading-Pics
PO, I really enjoyed that post. I have two tools like that, 45-70 and .357, I haven't tried either. You have motivated me to try.
Mike Johnson,
"Only those who will risk going too far, can possibly find out how far one can go." T.S. Eliot
"Only those who will risk going too far, can possibly find out how far one can go." T.S. Eliot
- Griff
- Posting leader...
- Posts: 20976
- Joined: Sat Mar 31, 2007 4:56 pm
- Location: OH MY GAWD they installed a STOP light!!!
Re: Campfire reloading-Pics
Perry,
Really great to see ya posting again. It appears you made it thru the delay in getting yer shooting irons and equipment from the impound. Although it would be almost criminal to alter that tool, is the misalignment due to wear on the pivot? Maybe a bushing would tighten up the tool and allow a smooth bullet outta the mold and help with any issues alignment of the tool halves.
Once again, good to see ya, and kudos for attempting to bring the old tool to life.
Really great to see ya posting again. It appears you made it thru the delay in getting yer shooting irons and equipment from the impound. Although it would be almost criminal to alter that tool, is the misalignment due to wear on the pivot? Maybe a bushing would tighten up the tool and allow a smooth bullet outta the mold and help with any issues alignment of the tool halves.
Once again, good to see ya, and kudos for attempting to bring the old tool to life.
Griff,
SASS/CMSA #93
NRA Patron
GUSA #93
There is a fine line between hobby & obsession!
AND... I'm over it!!
No I ain't ready, but let's do it anyway!
SASS/CMSA #93
NRA Patron
GUSA #93
There is a fine line between hobby & obsession!
AND... I'm over it!!
No I ain't ready, but let's do it anyway!
- O.S.O.K.
- Advanced Levergunner
- Posts: 5533
- Joined: Sun Apr 27, 2008 4:15 pm
- Location: Deep in the Piney Woods of Mississippi
Re: Campfire reloading-Pics
Very cool. Thanks for sharing that. Perhaps a load with the Tiple 7 will do better? Maybe with a vegetable fiber wad between charge and bullet? I bet if you worked on it a bit, you could make it shoot as well as the other...
NRA Endowment Life
Phi Kappa Sigma, Alpha Phi 83 "Skulls"
OCS, 120th MP Battalion, MSSG
MOLON LABE!
Phi Kappa Sigma, Alpha Phi 83 "Skulls"
OCS, 120th MP Battalion, MSSG
MOLON LABE!
- Sixgun
- Posting leader...
- Posts: 19131
- Joined: Sun Sep 16, 2007 7:17 pm
- Location: S.E. Pa. Where The Finest Winchesters & Colts Reside
Re: Campfire reloading-Pics
Perry, neat story. Thanks for sharing. I too, have the exact loading tool you have in the same caliber. I cast bullets up with it and when I'm feeling nostalgic, I shoot them in a Colt Lightning. ------------Sixgun
- KirkD
- Desktop Artiste
- Posts: 4406
- Joined: Sat Apr 07, 2007 6:52 am
- Location: Central Ontario, Canada
- Contact:
Re: Campfire reloading-Pics
Perry, that was very good reading. I especially congratulate you for doing your casting at a campfire. I imagine it is a bit more challenging to keep the melt temperature at the right level.
Kirk: An old geezer who loves the smell of freshly turned earth, old cedar rail fences, wood smoke, a crackling fireplace on a snowy evening, pristine wilderness lakes, the scent of
cedars and a magnificent Whitetail buck framed in the semi-buckhorn sights of a 120-year old Winchester.
Blog: https://www.kirkdurston.com/
cedars and a magnificent Whitetail buck framed in the semi-buckhorn sights of a 120-year old Winchester.
Blog: https://www.kirkdurston.com/
-
- Levergunner 3.0
- Posts: 516
- Joined: Fri Sep 07, 2007 4:59 am
- Location: Fly Over Country
Re: Campfire reloading-Pics
Excellent range report!!!
That looks like a 4 inch group at 50 meters, with a stray I'd disregard.
I would not feel safe; hiding behind that target!
That you cast those bullets Perry, in the old world method with original tooling...is true craftmanship.
Superb!!!
That looks like a 4 inch group at 50 meters, with a stray I'd disregard.
I would not feel safe; hiding behind that target!
That you cast those bullets Perry, in the old world method with original tooling...is true craftmanship.
Superb!!!