Bent Magazine Tube

Welcome to the Leverguns.Com Forum. This is a high-class place so act respectable. We discuss most anything here ... politely.

Moderators: AmBraCol, Hobie

Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.

Please post political post in the new Politics forum.
Post Reply
BakerT12
Levergunner
Posts: 1
Joined: Tue Jan 26, 2021 2:27 am

Bent Magazine Tube

Post by BakerT12 »

Howdy y’all. I’ve got a Rossi 92 in 45 LC, and I bent the magazine tube when my 4 wheeler went rolling down a 30 foot bluff while I was chasing cows in the mountains. Is there any way I can straighten it to where the rifle will work just fine? Or does anybody know where I can get a replacement?
User avatar
marlinman93
Advanced Levergunner
Posts: 6432
Joined: Sun Apr 01, 2007 3:40 pm
Location: Oregon

Re: Bent Magazine Tube

Post by marlinman93 »

You can buy universal tube material already blued, and then just drill the holes needed to match the old tube. Or you could check Numrich Gun Parts to see if they have replacement tubes for the Rossi.
Pre WWI Marlins and Singleshot rifles!
http://members.tripod.com/~OregonArmsCollectors/
Rockrat
Levergunner 2.0
Posts: 439
Joined: Wed Dec 19, 2018 8:35 pm
Location: Colorado

Re: Bent Magazine Tube

Post by Rockrat »

Depending on how badly bent, you might be able to take some steel round stock that just fits in the tube and radius the end. Then heat the damaged area and drive the round stock thru the heated tube.
User avatar
Sixgun
Posting leader...
Posts: 18563
Joined: Sun Sep 16, 2007 7:17 pm
Location: S.E. Pa. Where The Finest Winchesters & Colts Reside

Re: Bent Magazine Tube

Post by Sixgun »

Rockrat has it right.

I've done that but the metal can't be kinked. If it is you will have to hammer it at the kinked area while the mandrel is inside the tube.

After straightening it I've even seen it when people just turn the the tube either upside down or switch the front to the rear and redrilled the holes.

It's a common size, just measure the inside/outside diameter and buy a replacement from Brownells.----006
Model A Uzi’s
Image
User avatar
jeepnik
Advanced Levergunner
Posts: 6830
Joined: Sun Apr 08, 2007 1:39 pm
Location: On the Beach

Re: Bent Magazine Tube

Post by jeepnik »

Since no one mentioned it, I hope you weren’t on the four wheeler when it went down the bluff.

As to repairs I’d contact Rossi.
Jeepnik AKA "Old Eyes"
"Go low, go slow and preferably in the dark" The old Sarge (he was maybe 24.
"Freedom is never more that a generation from extinction" Ronald Reagan
"Every man should have at least one good rifle and know how to use it" Dad
User avatar
gamekeeper
Spambot Zapper
Posts: 17322
Joined: Thu Sep 06, 2007 3:32 pm
Location: Over the pond unfortunately.

Re: Bent Magazine Tube

Post by gamekeeper »

If more men loved and cherished their wives as much as I love bacon the world would be a much better place.
piller
Posting leader...
Posts: 15188
Joined: Sat Sep 29, 2007 9:49 pm
Location: South of Dallas

Re: Bent Magazine Tube

Post by piller »

Several good ideas on here. I would check with Rossi first to see if warranty work would be possible.
D. Brian Casady
Quid Llatine Dictum Sit, Altum Viditur.
Advanced is being able to do the basics while your leg is on fire---Bill Jeans
Don't ever take a fence down until you know why it was put up---Robert Frost
User avatar
marlinman93
Advanced Levergunner
Posts: 6432
Joined: Sun Apr 01, 2007 3:40 pm
Location: Oregon

Re: Bent Magazine Tube

Post by marlinman93 »

If it requires sending it to Rossi, vs. them selling you the tube, I wouldn't send it. The cost of shipping back and forth will make the repair too high.
here's a .45 Colt tube at Gun Parts Co. that for an Armi that might be a good start.

https://www.gunpartscorp.com/products/1527030
Pre WWI Marlins and Singleshot rifles!
http://members.tripod.com/~OregonArmsCollectors/
User avatar
mikld
Advanced Levergunner
Posts: 2336
Joined: Sat Dec 15, 2007 12:46 pm
Location: So. Orygun!

Re: Bent Magazine Tube

Post by mikld »

Also try Steve's Gunz aka Nate Kiowa Jones. He is the Rossi lever gun specialist... https://store.stevesgunz.com/index.php? ... urers_id=3
Mike
Vocatus atque non vocatus, Deus aderit...
I've learned how to stand on my own two knees...
Post Reply