Replacing brass??

Welcome to the Leverguns.Com Forum. This is a high-class place so act respectable. We discuss most anything here ... politely.

Moderators: Hobie, AmBraCol

Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.

Please post political post in the new Politics forum.
Post Reply
jkbrea
Levergunner 3.0
Posts: 995
Joined: Tue Dec 18, 2007 6:37 pm
Location: S. of Jackson, Wyoming

Replacing brass??

Post by jkbrea »

I just found out about this type of ammo and haven't really read up too much on it yet. Maybe it's just me!
It just surprised me. Composite cases!
Apparently not reloadable so can't replace brass...

https://www.tvammo.com/
1894cfan
Levergunner 3.0
Posts: 815
Joined: Tue Sep 11, 2007 1:07 am

Re: Replacing brass??

Post by 1894cfan »

If I can't reload it, I'll pass!
piller
Posting leader...
Posts: 12863
Joined: Sat Sep 29, 2007 9:49 pm
Location: South of Dallas

Re: Replacing brass??

Post by piller »

Only 1 thing I can think of, is that it might be lighter.
D. Brian Casady
Quid Llatine Dictum Sit, Altum Viditur.
Advanced is being able to do the basics while your leg is on fire---Bill Jeans
Don't ever take a fence down until you know why it was put up---Robert Frost
Ray Newman
Senior Levergunner
Posts: 1769
Joined: Mon Dec 10, 2007 12:43 pm
Location: Between No Where & No Place, WA

Re: Replacing brass??

Post by Ray Newman »

Several years ago, I read about the german attempts towards the end of WW II to manufacture caseless ammunition. From what i recall, the war ended before it could perfected. The US tried to do the same, but it seems that the ammunition components and powder caused the bore and chamber to foul excessively, so the idea was abandoned. Since then I have reda of a few others trying to do the same, but it just never seemed to gain any traction.
The most important aspect of this signature line is that you don't realize it doesn't say anything significant until you are just about done reading it & then it is too late to stop reading it....
Grand Poo Bah WA F.E.S.

In real life may you be the bad butt that you claim to be on social media.
Scott Tschirhart
Levergunner 3.0
Posts: 859
Joined: Fri Oct 16, 2020 2:56 pm
Location: San Antonio, Texas

Re: Replacing brass??

Post by Scott Tschirhart »

This isn't a new idea. I remember in the 1980s there was a company that was pushing a composite case with a steel head and a plastic body. We have also seen steel case heads that screwed into the bottom of a brass case. This ad says that the cases are magnetically retrievable, so I think there is a steel component in this as well.

A cartridge case is nothing more than a gasket when you get right down to it. Under current technology, brass works well. But brass is expensive and I think people will continue to seek cheaper alternatives.

Caseless ammunition is an interesting concept that we have explored since the 1860s and maybe earlier. But we are not there yet. We still need something to seal the breach.
User avatar
JimT
Shootist
Posts: 2650
Joined: Thu Sep 06, 2007 5:04 pm

Re: Replacing brass??

Post by JimT »

There are other companies producing the "brass replacement" cartridges. All have something that is stronger - lighter - more efficient - or some other thing. None offer what brass does. All are expensive. All are not reloadable unless you use special equipment. Reloaders are (or used to be) a small share of the shooting public. Bullet casters were even a small group. None of the "newer" "better" brass "replacement" appeals to me, but I am an old fanny burp of the Old School and what do I know? :roll: :lol:
User avatar
Ysabel Kid
Moderator
Posts: 25399
Joined: Mon Sep 17, 2007 7:10 pm
Location: South Carolina, USA
Contact:

Re: Replacing brass??

Post by Ysabel Kid »

Only time I will use non-brass cases is when chasing the brass is really a pain in the...

If I know where I am shooting will be a challenge to collect the brass, then a cheaper non-brass case is what I will use. Unfortunately, I have a lot from the last great ammo shortage (BHO years). Beggars could not be choosers back then (or now).
Image
User avatar
Grizz
Advanced Levergunner
Posts: 8478
Joined: Fri Aug 31, 2007 7:15 pm

Re: Replacing brass??

Post by Grizz »

i like Scott's "the brass is a gasket" point. it is also a springy gasket, which i "think" is the main benefit of brass. cartridge brass gets recycled. i remember seeing several 1000 pound totes sitting in a recycle center.
Post Reply