Rendering a Browning 1886 action to semipistol grip

Welcome to the Leverguns.Com Forum. This is a high-class place so act respectable. We discuss most anything here ... politely.

Moderators: AmBraCol, Hobie

Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.

Please post political post in the new Politics forum.
Post Reply
Naphtali
Levergunner 2.0
Posts: 457
Joined: Sun Apr 27, 2008 2:21 pm
Location: Montana

Rendering a Browning 1886 action to semipistol grip

Post by Naphtali »

I believe all Grade 1 Browning M1886 actions have straight grips. What is the least expensive procedure to render the action only to semipistol grip? What kind of dollars are we talking about?

I understand some custom gunsmiths convert grip assemblies from one to another. I also believe USRAC/Winchester replacement parts will fit the Browning receiver.
It's so simple to be wise. Just think of something stupid to say and then don't say it. Sam Levinson
User avatar
Mike D.
***Rock Star***
Posts: 4234
Joined: Sun Apr 01, 2007 4:56 pm
Location: Northern CA

Re: Rendering a Browning 1886 action to semipistol grip

Post by Mike D. »

You will need a lower tang, lever, and PG stock from Winchester. I converted one of my 1886 Extra Lights to a full mag, PG configuration using these parts, as well as others from MGW.

This is the Winchester lower tang as currently manufactured
Image
Tang and lever installed, along with Browning hammer and trigger/sear
Image
Winchester PG lever at top, original 71 lever below
Image
Front end with mag ring and FM
Image
The completed gun. Just something a little different.
Image
"Congressmen who willfully take actions during wartime that damage morale, and undermine the military are saboteurs and should be arrested, exiled or hanged"....President Abraham Lincoln
Naphtali
Levergunner 2.0
Posts: 457
Joined: Sun Apr 27, 2008 2:21 pm
Location: Montana

Re: Rendering a Browning 1886 action to semipistol grip

Post by Naphtali »

Mike D. wrote:You will need a lower tang, lever, and PG stock from Winchester. I converted one of my 1886 Extra Lights to a full mag, PG configuration using these parts, as well as others from MGW. . . .
Mike:

Great stuff, especially the graphics. You appear to have done what I want to do. A couple of follow-up questions. I have a USRAC/Winchester M1886 and a Browning M71. Regarding the two levers, I have not had these rifles through a winter [hunt] yet. While my hands are very small, and I have had no problem operating/shooting either rifle when wearing gloves with shooting glove's index finger partially amputated, I am concerned there will be a problem. In your experience does either of the two levers offer easier, surer manipulation in cold (0-20 degrees) weather?
***
I just got back from wandering in Lolo National Forest. Saw the remains of grizzly-killed deer -- too brutal a job to have been done by a mountain lion. It was dismembered as though it were blown up -- shattered pelvis, femur's ball socket cracked and broken. Where I was there would be no shooting beyond long pistol shot. And no there has been no vehicle where I was since who knows when.
It's so simple to be wise. Just think of something stupid to say and then don't say it. Sam Levinson
User avatar
Mike D.
***Rock Star***
Posts: 4234
Joined: Sun Apr 01, 2007 4:56 pm
Location: Northern CA

Re: Rendering a Browning 1886 action to semipistol grip

Post by Mike D. »

I cannot honestly answer your question because living in CA I have no hunting experience with temperatures anywhere near that low. All our seasons are over before winter sets in and my out of state hunts have also been in warmer situations. Maybe our upcoming deer and elk hunt to Colorado this coming November will expose me to some actual cold weather.
"Congressmen who willfully take actions during wartime that damage morale, and undermine the military are saboteurs and should be arrested, exiled or hanged"....President Abraham Lincoln
Post Reply