You'd think a rubber O-ring covered by grease would last forever, but mine have not. A long time for sure but apparently not "forever", because I have been having the occasional O-ring failure for several years in the dies I use with the Lyman 45 lube-sizer. My dies are kinda' old -- some of them are from Herter's. To be fair, the Herter's dies and the older Lyman dies were made back in the "good old days" when they made 'em to tighter tolerances and didn't use O-rings. And maybe we accepted a little lube leakage also. But however long they've been making O-ring bullet size dies is probably how old my dies are that have started giving me O-ring failures.
The hardware store O-rings I've tried were either a bit too small and leaked or were a tad large and tore up on insertion and then really leaked. I tried a selection from "The O-Ring Store" https://www.theoringstore.com/. Since these were probably 1/16th size to begin with my first guess was to use 1.6mm, but those leaked a bit. The ones that seem to work perfect are marked as "1.78mmX14mm" from their Buna-N 70 Duro series.
I can quit raiding other dies when I have a project now and just replace the leaky ones with new ones. Much better!
No I didn't get rid of the Star sizer -- it still does 90% of my bullet lube-sizing. But there are a few things for which I still use the old Lyman 45. In fact, I just acquired a second one so I could keep two types of lube in them. Yeah, a 45. I don't trust them new-fangled 450's.
New O-rings for old bullet size dies
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
- earlmck
- Advanced Levergunner
- Posts: 3447
- Joined: Tue Nov 30, 2010 12:10 am
- Location: pert-neer middle of Oregon
New O-rings for old bullet size dies
The greatest patriot...
is he who heals the most gullies. Patrick Henry
is he who heals the most gullies. Patrick Henry
- GunnyMack
- Advanced Levergunner
- Posts: 10286
- Joined: Mon Sep 19, 2016 7:57 am
- Location: Not where I want to be!
Re: New O-rings for old bullet size dies
Good fix for sure! Nice when you can keep stuff working.
BROWN LABS MATTER !!
- AJMD429
- Posting leader...
- Posts: 32291
- Joined: Sun Sep 09, 2007 10:03 am
- Location: Hoosierland
- Contact:
Re: New O-rings for old bullet size dies
A zillion sizes of O-rings I can understand, because the things they go in have varying tolerances and so on, but what drives me nuts is how many Allen/hex-wrench sizes there are. Then the tolerances are so lousy that even with a set of metrics and a set of standards, you get sloppy enough fit that the edges swage off of the wrench or the flats swage concavities on the screws.
Doctors for Sensible Gun Laws
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.
Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.
Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
-
- Advanced Levergunner
- Posts: 4296
- Joined: Wed Sep 15, 2010 12:57 pm
- Location: Vinita, I.T.
Re: New O-rings for old bullet size dies
I sympathize with you Earl. Two Herters presses, Herters powder measure and a bunch of Herters dies. And I still use the Lyman 45 luber/sizer. That 70 number is the Shore value and indicates the hardness of the rubber and that is critical for holding lots of pressure. My old Lyman 45 no longer uses the brass ring to hold pressure on the lube cylinder but has 80 shore O rings on a piston I made for it. I really need it to seat gas checks with.
M. M. Wright, Sheriff, Green county Arkansas (1860)
Currently living my eternal life.
NRA Life
SASS
ITSASS
Currently living my eternal life.
NRA Life
SASS
ITSASS
-
- Advanced Levergunner
- Posts: 4145
- Joined: Fri Dec 21, 2007 11:34 am
- Location: north of Palacios about 1400 miles
Re: New O-rings for old bullet size dies
Earl have you tried O-rings from NAPA meant fir hydraulic fittings? Todd/3leg
30/30 Winchester: Not accurate enough fer varmints, barely adequate for small deer; BUT In a 10" to 14" barrelled pistol; is good for moose/elk to 200 yards; ground squirrels to 300 metres
250 Savage... its what the 223 wishes it could be...!
250 Savage... its what the 223 wishes it could be...!
Re: New O-rings for old bullet size dies
Grainger has a ton of different O-rings. Got a bag for spares for my star sizer! I seem to cut them when I am changing dies in that machine.
Heck I even found one that fits as a drive belt for my thumbler tumbler! Got tired of buying spares, from thumbler, to only have them degrade sitting in the cabinet.
Heck I even found one that fits as a drive belt for my thumbler tumbler! Got tired of buying spares, from thumbler, to only have them degrade sitting in the cabinet.
Gettin old ain't for sissies!
There just has to be dogs in heaven !
There just has to be dogs in heaven !
- earlmck
- Advanced Levergunner
- Posts: 3447
- Joined: Tue Nov 30, 2010 12:10 am
- Location: pert-neer middle of Oregon
Re: New O-rings for old bullet size dies
No Todd, I didn't try anything other than the 1/16th (just barely too small) and the 3/32 (definitely too big) that were available at the local "Ace". Then I did the lazy thing and googled "O-rings". I now have two lifetime supplies of the things -- anybody need a few?3leggedturtle wrote: ↑Wed Nov 06, 2019 12:36 pm Earl have you tried O-rings from NAPA meant fir hydraulic fittings? Todd/3leg
Many years ago I bought a die that was a dang tight fit and I suspect I made the sizer opening a bit larger in the process of forcing the oversized die into it. Been slightly leaky ever since. I'd suspect those 1/16th O-rings would work for most folks, but those slightly larger metrics seem like just what I needed.
The greatest patriot...
is he who heals the most gullies. Patrick Henry
is he who heals the most gullies. Patrick Henry
-
- Levergunner 3.0
- Posts: 996
- Joined: Fri Oct 24, 2008 9:19 pm
- Location: South East South Dakota
Re: New O-rings for old bullet size dies
The oringstore. Huh. Thanks Earl, that looks to be a handy site.
Cat
Cat