Winchester 94 38-55
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
- Rube Burrows
- Advanced Levergunner
- Posts: 2124
- Joined: Tue Oct 19, 2010 12:27 pm
- Location: Louisiana
Winchester 94 38-55
Hey everyone. I have not been on in a while. Been pretty focused lately on my tintype and ambrotype photography. Hope everyone has been good.
That said, I put together this Post 64 Winchester 94 a few years ago. It started out life as a 1979 20" Carbine 30-30.
I had a couple hundred rounds of 38-55 that I got from someone but now that that stuff is almost shot up I have been thinking about reloading for this one. I have reloaded for 45 Colt, 38/.357 and 44mag for a long time now but have not yet done anything for rifle calibers but this being a pretty straight walled I figured it would be pretty straight forward.
I have been seeing some things though that I have questions about though.
1) I am seeing brass that is 2.082" and brass that is 2.125". Is there a reason for the different sizes?
2) I have read that there were different chambers for the 38-55. Is this true and why if so?
My barrel is one of the barrels from Numrich.
3) Any pointers on reloading for this caliber?
4) Is there a preferred bullet for this rifle? I am mostly just target shooting but may like to hunt with it next season.
That said, I put together this Post 64 Winchester 94 a few years ago. It started out life as a 1979 20" Carbine 30-30.
I had a couple hundred rounds of 38-55 that I got from someone but now that that stuff is almost shot up I have been thinking about reloading for this one. I have reloaded for 45 Colt, 38/.357 and 44mag for a long time now but have not yet done anything for rifle calibers but this being a pretty straight walled I figured it would be pretty straight forward.
I have been seeing some things though that I have questions about though.
1) I am seeing brass that is 2.082" and brass that is 2.125". Is there a reason for the different sizes?
2) I have read that there were different chambers for the 38-55. Is this true and why if so?
My barrel is one of the barrels from Numrich.
3) Any pointers on reloading for this caliber?
4) Is there a preferred bullet for this rifle? I am mostly just target shooting but may like to hunt with it next season.
You do not have the required permissions to view the files attached to this post.
- fordwannabe
- Advanced Levergunner
- Posts: 3371
- Joined: Thu Apr 02, 2009 8:52 am
- Location: Womelsdorf PA
Re: Winchester 94 38-55
Good to see you again. I use the lee 250 grain bullet. The biggest thing I see is slugging your barrel to see where to start with bullet sizing. Pm on the way.
a Pennsylvanian who has been accused of clinging to my religion and my guns......Good assessment skills.
- Rube Burrows
- Advanced Levergunner
- Posts: 2124
- Joined: Tue Oct 19, 2010 12:27 pm
- Location: Louisiana
Re: Winchester 94 38-55
Thanks. Checking now.
- vancelw
- Advanced Levergunner
- Posts: 3950
- Joined: Mon Sep 28, 2009 1:56 pm
- Location: 90% NE Texas and 10% SE Montana
Re: Winchester 94 38-55
For hunting I use Barnes Original 255 gr in .377 caliber.
For cast I have a Lyman .379 bullets but really haven't shot my Chief Crazy Horse rifle in several years....too much work and no play.
For cast I have a Lyman .379 bullets but really haven't shot my Chief Crazy Horse rifle in several years....too much work and no play.
"Make yourself an honest man, and then you may be sure that there is one less scoundrel in the world." - Thomas Carlyle
- Rube Burrows
- Advanced Levergunner
- Posts: 2124
- Joined: Tue Oct 19, 2010 12:27 pm
- Location: Louisiana
-
- Advanced Levergunner
- Posts: 9426
- Joined: Sun Jun 29, 2008 10:05 am
- Location: The Land of Enchantment
Re: Winchester 94 38-55
Rube, I agree -- really nice "build," and you sure chose a fine caliber.
Back when I was swaging jacketed bullets, I swaged a 220-grain soft point .379 slug specifically for the Marlin Cowboy that was briefly in production, and it was spectacularly accurate.
If that Numrich barrel is .375 in the grooves, whole different story.
Back when I was swaging jacketed bullets, I swaged a 220-grain soft point .379 slug specifically for the Marlin Cowboy that was briefly in production, and it was spectacularly accurate.
If that Numrich barrel is .375 in the grooves, whole different story.
-
- Levergunner 2.0
- Posts: 393
- Joined: Thu Nov 19, 2009 8:06 am
- Location: Junction City Oregon
Re: Winchester 94 38-55
Really nice rifle, thanks for showing it to us.
- Rube Burrows
- Advanced Levergunner
- Posts: 2124
- Joined: Tue Oct 19, 2010 12:27 pm
- Location: Louisiana
Re: Winchester 94 38-55
Bill in Oregon wrote: ↑Mon Feb 04, 2019 10:49 am Rube, I agree -- really nice "build," and you sure chose a fine caliber.
Back when I was swaging jacketed bullets, I swaged a 220-grain soft point .379 slug specifically for the Marlin Cowboy that was briefly in production, and it was spectacularly accurate.
If that Numrich barrel is .375 in the grooves, whole different story.
I will be slugging the barrel soon to try to find out what it measures.
- Rube Burrows
- Advanced Levergunner
- Posts: 2124
- Joined: Tue Oct 19, 2010 12:27 pm
- Location: Louisiana
Re: Winchester 94 38-55
Thanks for the info and I know the feeling of too much work and not enough play.
- Rube Burrows
- Advanced Levergunner
- Posts: 2124
- Joined: Tue Oct 19, 2010 12:27 pm
- Location: Louisiana
Re: Winchester 94 38-55
Thanks.
-
- Advanced Levergunner
- Posts: 2502
- Joined: Tue Sep 04, 2007 1:24 pm
- Location: wasilla, alaska and bozeman, montana
Re: Winchester 94 38-55
Bill in Oregon wrote: ↑Mon Feb 04, 2019 10:49 am Rube, I agree -- really nice "build," and you sure chose a fine caliber.
Back when I was swaging jacketed bullets, I swaged a 220-grain soft point .379 slug specifically for the Marlin Cowboy that was briefly in production, and it was spectacularly accurate.
If that Numrich barrel is .375 in the grooves, whole different story.
that reminds me ! I still have some of your bullets - they shot very well ! ...and I need to find them now that my reloading room is getting set up again......of course my old Winchester 1894 38/55 is still in the hospital getting its stock repaired.
cable
-
- Advanced Levergunner
- Posts: 9426
- Joined: Sun Jun 29, 2008 10:05 am
- Location: The Land of Enchantment
Re: Winchester 94 38-55
Harold, do tell! That's been a long time ago.
-
- Advanced Levergunner
- Posts: 2502
- Joined: Tue Sep 04, 2007 1:24 pm
- Location: wasilla, alaska and bozeman, montana
Re: Winchester 94 38-55
I've never read why SAAMI standardized on the 2.082". The original spec was for 2-1/8". I imagine Winchester or the like made runs of .38-55 with the brass trimmed back a bit (perhaps to mate up with some bullets they had on hand) and eventually ended up cutting their chambers for that. The necked down variant, the .32-40, never was trimmed back, even for "fixed" ammo (as opposed to breech seated).
I've read the bore diameters are all over the place, with the SAAMI number being an atypical size.
Re: Winchester 94 38-55
I have a Numrich 38-55 barrel, I've yet to fit to a model 94, my groove diameter is .375 with a 1 in 14 twist.
regards Dallas
regards Dallas
It's dead easy to die; it's the keeping on living that's hard - Douglas Mawson - Scientist and polar survivor
-
- Levergunner 2.0
- Posts: 153
- Joined: Mon Oct 06, 2008 7:16 am
Re: Winchester 94 38-55
I will have to check when I get back home this weekend. I bought the starline long brass for whatever reason I decided was
wise after reading the excellent article on their website. I load for a Marlin Cowboy and a Moroku/Win 1885. I am using The Missouri 245 grain bullet. I found the long starline a little too long if seating in the crimp groove. I have trimmed all of mine to 2.110 and it works in both rifles.
wise after reading the excellent article on their website. I load for a Marlin Cowboy and a Moroku/Win 1885. I am using The Missouri 245 grain bullet. I found the long starline a little too long if seating in the crimp groove. I have trimmed all of mine to 2.110 and it works in both rifles.
- Rube Burrows
- Advanced Levergunner
- Posts: 2124
- Joined: Tue Oct 19, 2010 12:27 pm
- Location: Louisiana
- Rube Burrows
- Advanced Levergunner
- Posts: 2124
- Joined: Tue Oct 19, 2010 12:27 pm
- Location: Louisiana
Re: Winchester 94 38-55
Fisher-Price wrote: ↑Mon Feb 04, 2019 9:25 pm I will have to check when I get back home this weekend. I bought the starline long brass for whatever reason I decided was
wise after reading the excellent article on their website. I load for a Marlin Cowboy and a Moroku/Win 1885. I am using The Missouri 245 grain bullet. I found the long starline a little too long if seating in the crimp groove. I have trimmed all of mine to 2.110 and it works in both rifles.
Good deal. I think my rifle likes the shorter rounds for sure depending on what bullet I use.
Re: Winchester 94 38-55
February 8, 2019
Dear Mr. Burrows,
Welcome to the cult of the .38/55. I am sure you will have a great time handloading and shooting the old “pumpkin roller”.
I have been loading for and shooting a rifle very similar to yours for over fifteen years. Mine started life as .30-30 circa 1940. The previous owner re-barreled it to .38/55 (26 inch, round) , color case hardened the action, lever, crescent butt plate, and fore-end cap and topped it off with nicely figured walnut butt stock and fore-end. I had a gunsmith install a Marbles tang peep sight.
You asked about the differences in case length. According to an article in Precision Shooting magazine (April, 2001) by M.L.McPherson, when the .38/55 was first introduced by Winchester the cartridge length was 2.130 inches but was reduced to 2.075 inches at a later date. Both cartridge lengths are available today. I have been using the shorter of the two which is more readily available currently.
As Levergunner “fordwammabe” has suggested, slug the bore to determine the groove diameter and then select bullets that are 0.001 to 0.002 inches larger in diameter. The barrel on my rifle measured 0.375 inches so I use cast lead bullets sized 0.376 and 0.377 inches in diameter.
I pursued through the more than 450 target I have shot through the years and cherry picked some load that worked well for me that I would like to pass on to you if you don't mind. All my targets were shot a fifty yards from a bench rest at a three inch bullseye that the front sight just covered. Velocities quoted are an average of five shots.
Winchester cases, CCI #200 primers, 21 grains of IMR-4198, SAECO #373 250 grain cast lead bullet with gas check,0.376 inches diameter, OAL=2.50 inches, Lee crimped. Average velocity was 1544 fps and the best group measured 1 5/16 inches.
Winchester cases, CCI #200 primers, 27 grains of IMR-3031, same bullet as above, OAL=2.43 inches, Lee crimped. Average velocity was 1574 fps and the best group measured 13/16th inches (luck).
Same cases, primers, and bullets as above, 23.3 grains of RL-7, OAL=2.49 inches, Lee crimped. Average velocity was 1489 fps and the best group measured 13/16th inches (again,luck).
Winchester cases, WLR primers, 23.3 grains RL-7, 260 grain 0.377 inch diameter cast lead, gas-check RNFP bullets from Bonus Bullets, OAL=2.46 inches, Lee crimped. Average velocity was 1518 fps and the best group measured 1 inch (three shots in ½ inch).
Winchester cases, WLR primers, 23.5 grains of H-322, Bonus Bullets RNFP. 260 grain cast lead, gas check 0.377 inch diameter bullets, OAL=2.46 inches, Lee crimped. Average muzzle velocity was 1473 fps and the best group measured 1 3/16th inches.
Winchester cases, WLR primers, 23.3 grains of RL-7, Oregon Trail Laser Cast RNFP 240 grain 0.377 inch diameter cast lead bullet without a gas check, OAL=2.51, Lee crimped. Average muzzle velocity was 1434 fps and the best group measured 7/8th inches. Three shots in 3/8th inch (luck again).
Winchester cases, WLR primers, 20.5 grains of IMR-4198, Oregon Trail Laser Cast RNFP 240 grain 0.377 inch diameter cast lead bullets without a gas check, OAL= 2.51 inches, Lee crimped. Average muzzle velocity was 1405 fps and the best group measured 1 1/16th inches.
Winchester cases, WLR primers, 27 grains of IMR-3031, Oregon Trail Laser Cast 240 grain 0.377 inch diameter cast lead bullets without a gas check, OAL= 2.52 inches, Lee crimped. Average muzzle velocity was 1421 fps and the best group measured 1 inch (four shots in 11/16ths inches).
Winchester cases, CCI#200 primers, 20 grains of IMR-4198, Bearthooth LFNGC 250 grain cast lead gas check bullets 0.376 inch diameter. OAL=2.44 inches, Lee crimped. Average muzzle velocity was 1473 fps and the best group measured 1 ½ inches (four shots in7/16ths inches).
Winchester cases, WLR primers, 23.3 grains RL-7, Bearthooth LFNGC cast lead gas check 0.376 inch diameter bullets, OAL-2.44 inches, Lee crimped. Average muzzle velocity was 1520 fps and the best group measured 1 1/16ths inches (four shots in ½ inches).
I have tried some loads using JSP bullets from Barnes and Hawk that worked satisfactorily but I stick to cast lead bullets because they are much less expensive, my Model 94 seems to handle them better, and I only use it to shoot holes in paper targets anyway. I am not interested in hunting.
After all the experimenting, I have decided on the load using Winchester cases and large rifle primers, 23.3 grains of RL-7 powder, and Oregon Trail Laser Cast 240 grain bullets without a gas check sized 0.377 inches in diameter. It is a pleasant shooting load and sufficiently accurate for my purposes.
Of course, as an intelligent and careful handloader you will double check all suggested loads you receive from whatever source in at least two current handloading manuals. Resist the temptation to “hot rod” this caliber; muzzle velocities in the range of 1500 to 1600 fps should be sufficient. Good luck, good shooting, and keep us posted as to your results.
Dear Mr. Burrows,
Welcome to the cult of the .38/55. I am sure you will have a great time handloading and shooting the old “pumpkin roller”.
I have been loading for and shooting a rifle very similar to yours for over fifteen years. Mine started life as .30-30 circa 1940. The previous owner re-barreled it to .38/55 (26 inch, round) , color case hardened the action, lever, crescent butt plate, and fore-end cap and topped it off with nicely figured walnut butt stock and fore-end. I had a gunsmith install a Marbles tang peep sight.
You asked about the differences in case length. According to an article in Precision Shooting magazine (April, 2001) by M.L.McPherson, when the .38/55 was first introduced by Winchester the cartridge length was 2.130 inches but was reduced to 2.075 inches at a later date. Both cartridge lengths are available today. I have been using the shorter of the two which is more readily available currently.
As Levergunner “fordwammabe” has suggested, slug the bore to determine the groove diameter and then select bullets that are 0.001 to 0.002 inches larger in diameter. The barrel on my rifle measured 0.375 inches so I use cast lead bullets sized 0.376 and 0.377 inches in diameter.
I pursued through the more than 450 target I have shot through the years and cherry picked some load that worked well for me that I would like to pass on to you if you don't mind. All my targets were shot a fifty yards from a bench rest at a three inch bullseye that the front sight just covered. Velocities quoted are an average of five shots.
Winchester cases, CCI #200 primers, 21 grains of IMR-4198, SAECO #373 250 grain cast lead bullet with gas check,0.376 inches diameter, OAL=2.50 inches, Lee crimped. Average velocity was 1544 fps and the best group measured 1 5/16 inches.
Winchester cases, CCI #200 primers, 27 grains of IMR-3031, same bullet as above, OAL=2.43 inches, Lee crimped. Average velocity was 1574 fps and the best group measured 13/16th inches (luck).
Same cases, primers, and bullets as above, 23.3 grains of RL-7, OAL=2.49 inches, Lee crimped. Average velocity was 1489 fps and the best group measured 13/16th inches (again,luck).
Winchester cases, WLR primers, 23.3 grains RL-7, 260 grain 0.377 inch diameter cast lead, gas-check RNFP bullets from Bonus Bullets, OAL=2.46 inches, Lee crimped. Average velocity was 1518 fps and the best group measured 1 inch (three shots in ½ inch).
Winchester cases, WLR primers, 23.5 grains of H-322, Bonus Bullets RNFP. 260 grain cast lead, gas check 0.377 inch diameter bullets, OAL=2.46 inches, Lee crimped. Average muzzle velocity was 1473 fps and the best group measured 1 3/16th inches.
Winchester cases, WLR primers, 23.3 grains of RL-7, Oregon Trail Laser Cast RNFP 240 grain 0.377 inch diameter cast lead bullet without a gas check, OAL=2.51, Lee crimped. Average muzzle velocity was 1434 fps and the best group measured 7/8th inches. Three shots in 3/8th inch (luck again).
Winchester cases, WLR primers, 20.5 grains of IMR-4198, Oregon Trail Laser Cast RNFP 240 grain 0.377 inch diameter cast lead bullets without a gas check, OAL= 2.51 inches, Lee crimped. Average muzzle velocity was 1405 fps and the best group measured 1 1/16th inches.
Winchester cases, WLR primers, 27 grains of IMR-3031, Oregon Trail Laser Cast 240 grain 0.377 inch diameter cast lead bullets without a gas check, OAL= 2.52 inches, Lee crimped. Average muzzle velocity was 1421 fps and the best group measured 1 inch (four shots in 11/16ths inches).
Winchester cases, CCI#200 primers, 20 grains of IMR-4198, Bearthooth LFNGC 250 grain cast lead gas check bullets 0.376 inch diameter. OAL=2.44 inches, Lee crimped. Average muzzle velocity was 1473 fps and the best group measured 1 ½ inches (four shots in7/16ths inches).
Winchester cases, WLR primers, 23.3 grains RL-7, Bearthooth LFNGC cast lead gas check 0.376 inch diameter bullets, OAL-2.44 inches, Lee crimped. Average muzzle velocity was 1520 fps and the best group measured 1 1/16ths inches (four shots in ½ inches).
I have tried some loads using JSP bullets from Barnes and Hawk that worked satisfactorily but I stick to cast lead bullets because they are much less expensive, my Model 94 seems to handle them better, and I only use it to shoot holes in paper targets anyway. I am not interested in hunting.
After all the experimenting, I have decided on the load using Winchester cases and large rifle primers, 23.3 grains of RL-7 powder, and Oregon Trail Laser Cast 240 grain bullets without a gas check sized 0.377 inches in diameter. It is a pleasant shooting load and sufficiently accurate for my purposes.
Of course, as an intelligent and careful handloader you will double check all suggested loads you receive from whatever source in at least two current handloading manuals. Resist the temptation to “hot rod” this caliber; muzzle velocities in the range of 1500 to 1600 fps should be sufficient. Good luck, good shooting, and keep us posted as to your results.
- Rube Burrows
- Advanced Levergunner
- Posts: 2124
- Joined: Tue Oct 19, 2010 12:27 pm
- Location: Louisiana
Re: Winchester 94 38-55
Yodar wrote: ↑Fri Feb 08, 2019 4:43 pm February 8, 2019
Dear Mr. Burrows,
Welcome to the cult of the .38/55. I am sure you will have a great time handloading and shooting the old “pumpkin roller”.
I have been loading for and shooting a rifle very similar to yours for over fifteen years. Mine started life as .30-30 circa 1940. The previous owner re-barreled it to .38/55 (26 inch, round) , color case hardened the action, lever, crescent butt plate, and fore-end cap and topped it off with nicely figured walnut butt stock and fore-end. I had a gunsmith install a Marbles tang peep sight.
You asked about the differences in case length. According to an article in Precision Shooting magazine (April, 2001) by M.L.McPherson, when the .38/55 was first introduced by Winchester the cartridge length was 2.130 inches but was reduced to 2.075 inches at a later date. Both cartridge lengths are available today. I have been using the shorter of the two which is more readily available currently.
As Levergunner “fordwammabe” has suggested, slug the bore to determine the groove diameter and then select bullets that are 0.001 to 0.002 inches larger in diameter. The barrel on my rifle measured 0.375 inches so I use cast lead bullets sized 0.376 and 0.377 inches in diameter.
I pursued through the more than 450 target I have shot through the years and cherry picked some load that worked well for me that I would like to pass on to you if you don't mind. All my targets were shot a fifty yards from a bench rest at a three inch bullseye that the front sight just covered. Velocities quoted are an average of five shots.
Winchester cases, CCI #200 primers, 21 grains of IMR-4198, SAECO #373 250 grain cast lead bullet with gas check,0.376 inches diameter, OAL=2.50 inches, Lee crimped. Average velocity was 1544 fps and the best group measured 1 5/16 inches.
Winchester cases, CCI #200 primers, 27 grains of IMR-3031, same bullet as above, OAL=2.43 inches, Lee crimped. Average velocity was 1574 fps and the best group measured 13/16th inches (luck).
Same cases, primers, and bullets as above, 23.3 grains of RL-7, OAL=2.49 inches, Lee crimped. Average velocity was 1489 fps and the best group measured 13/16th inches (again,luck).
Winchester cases, WLR primers, 23.3 grains RL-7, 260 grain 0.377 inch diameter cast lead, gas-check RNFP bullets from Bonus Bullets, OAL=2.46 inches, Lee crimped. Average velocity was 1518 fps and the best group measured 1 inch (three shots in ½ inch).
Winchester cases, WLR primers, 23.5 grains of H-322, Bonus Bullets RNFP. 260 grain cast lead, gas check 0.377 inch diameter bullets, OAL=2.46 inches, Lee crimped. Average muzzle velocity was 1473 fps and the best group measured 1 3/16th inches.
Winchester cases, WLR primers, 23.3 grains of RL-7, Oregon Trail Laser Cast RNFP 240 grain 0.377 inch diameter cast lead bullet without a gas check, OAL=2.51, Lee crimped. Average muzzle velocity was 1434 fps and the best group measured 7/8th inches. Three shots in 3/8th inch (luck again).
Winchester cases, WLR primers, 20.5 grains of IMR-4198, Oregon Trail Laser Cast RNFP 240 grain 0.377 inch diameter cast lead bullets without a gas check, OAL= 2.51 inches, Lee crimped. Average muzzle velocity was 1405 fps and the best group measured 1 1/16th inches.
Winchester cases, WLR primers, 27 grains of IMR-3031, Oregon Trail Laser Cast 240 grain 0.377 inch diameter cast lead bullets without a gas check, OAL= 2.52 inches, Lee crimped. Average muzzle velocity was 1421 fps and the best group measured 1 inch (four shots in 11/16ths inches).
Winchester cases, CCI#200 primers, 20 grains of IMR-4198, Bearthooth LFNGC 250 grain cast lead gas check bullets 0.376 inch diameter. OAL=2.44 inches, Lee crimped. Average muzzle velocity was 1473 fps and the best group measured 1 ½ inches (four shots in7/16ths inches).
Winchester cases, WLR primers, 23.3 grains RL-7, Bearthooth LFNGC cast lead gas check 0.376 inch diameter bullets, OAL-2.44 inches, Lee crimped. Average muzzle velocity was 1520 fps and the best group measured 1 1/16ths inches (four shots in ½ inches).
I have tried some loads using JSP bullets from Barnes and Hawk that worked satisfactorily but I stick to cast lead bullets because they are much less expensive, my Model 94 seems to handle them better, and I only use it to shoot holes in paper targets anyway. I am not interested in hunting.
After all the experimenting, I have decided on the load using Winchester cases and large rifle primers, 23.3 grains of RL-7 powder, and Oregon Trail Laser Cast 240 grain bullets without a gas check sized 0.377 inches in diameter. It is a pleasant shooting load and sufficiently accurate for my purposes.
Of course, as an intelligent and careful handloader you will double check all suggested loads you receive from whatever source in at least two current handloading manuals. Resist the temptation to “hot rod” this caliber; muzzle velocities in the range of 1500 to 1600 fps should be sufficient. Good luck, good shooting, and keep us posted as to your results.
Thanks for all of the great information. That will def. give me some good starting points to check for when I start reloading for this rifle. This rifle will mostly be for target shooting also but may end up on a hunting trip or two now and then.
Re: Winchester 94 38-55
I don't have a dog in this fight, but thank you Yodar for sharing all this information. That is some fantastic data.
If you're gonna be stupid ya gotta be tough-
Isiah 55:8&9
It's easier to fool people than it is to convince them they have been fooled.
Isiah 55:8&9
It's easier to fool people than it is to convince them they have been fooled.
- Rube Burrows
- Advanced Levergunner
- Posts: 2124
- Joined: Tue Oct 19, 2010 12:27 pm
- Location: Louisiana
Re: Winchester 94 38-55
Seems mine keeps measuring out to .376. I measured it a few different ways trying to keep each side of the calipers on a land and my most consistent measurement comes out to 0.376
-
- Levergunner
- Posts: 39
- Joined: Tue Jan 15, 2019 9:06 am
Re: Winchester 94 38-55
Any updates? I'm considering getting a new Miroku in this caliber and intend to load for it. I imagine the new barrels would have a standard measurement I can get from them w/o having to gauge it myself.
- Rube Burrows
- Advanced Levergunner
- Posts: 2124
- Joined: Tue Oct 19, 2010 12:27 pm
- Location: Louisiana
Re: Winchester 94 38-55
Sevastopol wrote: ↑Sun Apr 21, 2019 6:06 pm Any updates? I'm considering getting a new Miroku in this caliber and intend to load for it. I imagine the new barrels would have a standard measurement I can get from them w/o having to gauge it myself.
Rifle has been shooting great. Shot it a few weeks ago. Got some bullets from Tom here and loaded up some rounds. Once I got the tang sight dialed in I was ringing steel pretty nicely.
- fordwannabe
- Advanced Levergunner
- Posts: 3371
- Joined: Thu Apr 02, 2009 8:52 am
- Location: Womelsdorf PA
Re: Winchester 94 38-55
Which Bullets did ya end up using and what
Load? Glad to be able to help.
Load? Glad to be able to help.
a Pennsylvanian who has been accused of clinging to my religion and my guns......Good assessment skills.
-
- Levergunner
- Posts: 39
- Joined: Tue Jan 15, 2019 9:06 am
Re: Winchester 94 38-55
Good to hear. Would also like to know your load.Rube Burrows wrote: ↑Sun Apr 21, 2019 8:27 pmSevastopol wrote: ↑Sun Apr 21, 2019 6:06 pm Any updates? I'm considering getting a new Miroku in this caliber and intend to load for it. I imagine the new barrels would have a standard measurement I can get from them w/o having to gauge it myself.
Rifle has been shooting great. Shot it a few weeks ago. Got some bullets from Tom here and loaded up some rounds. Once I got the tang sight dialed in I was ringing steel pretty nicely.
- marlinman93
- Advanced Levergunner
- Posts: 6639
- Joined: Sun Apr 01, 2007 3:40 pm
- Location: Oregon
Re: Winchester 94 38-55
McPherson is an idiot. When will this BS about Winchester introducing the .38-55 ever stop? Winchester didn't even have a rifle that the .38-55 was chambered in when the .38-55 was introduced!Yodar wrote: ↑Fri Feb 08, 2019 4:43 pmYou asked about the differences in case length. According to an article in Precision Shooting magazine (April, 2001) by M.L.McPherson, when the .38/55 was first introduced by Winchester the cartridge length was 2.130 inches but was reduced to 2.075 inches at a later date. Both cartridge lengths are available today. I have been using the shorter of the two which is more readily available currently.
The .38-55 started life as the .38-50 Ballard Everlasting, introduced by John Marlin. Marlin firearms Co. developed the cartridge for the Ballard rifles, and soon after it's inception they offered a thinner case wall that held 55 grs. of BP, and called it the .38-55 Ballard. It has always been a Marlin cartridge, and Winchester's early ammo for use in both Marlins, and Winchesters were labeled .38-55 Ballard. I've got boxes of original Winchester ammunition labeled this way, so even Winchester credited Marlin with this cartridge.
All .38-55 ammo was the longer version for decades, and guns made by all makers had the longer chambers too. Then Winchester came out with their .375 Winchester, which was simply the shorter length .38-55 brass loaded to pretty hot levels, and using .375" bullets instead of the earlier that ran around .379"-.381" Once Winchester began to produce the .375 ammo, they began to use the same length for all .375 and .38-55 brass. After that it wasn't long until it became tougher to find correct length .38-55 brass. Fortunately some cartridge makers listened to shooters complaints about the short brass, and began making the correct longer brass again.
Pre WWI Marlins and Singleshot rifles!
http://members.tripod.com/~OregonArmsCollectors/
http://members.tripod.com/~OregonArmsCollectors/
-
- Advanced Levergunner
- Posts: 9426
- Joined: Sun Jun 29, 2008 10:05 am
- Location: The Land of Enchantment
Re: Winchester 94 38-55
Vall, thanks for clearing the air and attributing the .38-55 to Marlin, as history affirms is the case.
- Rube Burrows
- Advanced Levergunner
- Posts: 2124
- Joined: Tue Oct 19, 2010 12:27 pm
- Location: Louisiana
Re: Winchester 94 38-55
fordwannabe wrote: ↑Sun Apr 21, 2019 9:34 pm Which Bullets did ya end up using and what
Load? Glad to be able to help.
I'm still going through them. 255 grain Lee .377 is what I loaded up first and it seems to like them pretty good. Next I am going to load up some of the .379s and see if it likes those better.
I am about to order up some new starline brass that way I can load them all up at one time. For now I was using some fired brass that I had.
- AJMD429
- Posting leader...
- Posts: 32800
- Joined: Sun Sep 09, 2007 10:03 am
- Location: Hoosierland
- Contact:
Re: Winchester 94 38-55
Yep. Such posts are the real meat of the leverguns forum; the other stuff is fun, but THIS is really cool....(and I don't even have a 38-55... )
Doctors for Sensible Gun Laws
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.
Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
"first do no harm" - gun control LAWS lead to far more deaths than 'easy access' ever could.
Want REAL change? . . . . . "Boortz/Nugent in 2012 . . . ! "
- Rube Burrows
- Advanced Levergunner
- Posts: 2124
- Joined: Tue Oct 19, 2010 12:27 pm
- Location: Louisiana
Re: Winchester 94 38-55
-
- Levergunner 2.0
- Posts: 393
- Joined: Thu Nov 19, 2009 8:06 am
- Location: Junction City Oregon
Re: Winchester 94 38-55
really nice gun, one of a kind, congratulations, great caliber also.
Re: Winchester 94 38-55
Good to see all this wonderful info on the 38-55. I just got a Crazy Horse 94, so I'm going to assume it needs the shorter brass? This CH rifle has a rather thin round barrel. I imagine when sighting in not to shoot more than 5 shot at a time, as the heating barrel will open up the group. Interesting thread.