Vintage Buck Saw Question.
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Re: Vintage Buck Saw Question.
They don't list them on their site that I can find, but I would send a picture or two to Crosscut Saw Co. in Seneca Falls, NY:
http://www.crosscutsaw.com/
I'll bet they can point you in the right direction, and may even be able to identify the blade. Plus, they have lots of really neat saw stuff to look through. They have been very helpful folks, in my dealings with them.
That really is a fine looking saw- nice find!
Good luck!
Regan
http://www.crosscutsaw.com/
I'll bet they can point you in the right direction, and may even be able to identify the blade. Plus, they have lots of really neat saw stuff to look through. They have been very helpful folks, in my dealings with them.
That really is a fine looking saw- nice find!
Good luck!
Regan
Running the ridges and rivers of Virginia's southern Appalachians
Re: Vintage Buck Saw Question.
If it comes to it, you could make new pins out of brass rod. You melt the end with an oxy-acetylene torch to form a ball, then put the pin through a hole in a steel plate and hammer the ball flatish (probably have to anneal once before you're done). Won't be as pretty as those, but functional. I used to make silver nails for small box hardware this way.
Neat saw, I really like the tensioning hardware
Neat saw, I really like the tensioning hardware
Re: Vintage Buck Saw Question.
Neato Keeno
The Rotten Fruit Always Hits The Ground First
Proud Life Member Of:
NRA
Second Amendment Foundation
Citizens Committee For The Right To Keep And Bear Arms
DAV
Proud Life Member Of:
NRA
Second Amendment Foundation
Citizens Committee For The Right To Keep And Bear Arms
DAV
- Griff
- Posting leader...
- Posts: 20864
- Joined: Sat Mar 31, 2007 4:56 pm
- Location: OH MY GAWD they installed a STOP light!!!
Re: Vintage Buck Saw Question.
But... but... it requires... Manual Labor' to run...
Griff,
SASS/CMSA #93
NRA Patron
GUSA #93
There is a fine line between hobby & obsession!
AND... I'm over it!!
No I ain't ready, but let's do it anyway!
SASS/CMSA #93
NRA Patron
GUSA #93
There is a fine line between hobby & obsession!
AND... I'm over it!!
No I ain't ready, but let's do it anyway!
Re: Vintage Buck Saw Question.
LOL GriffGriff wrote:But... but... it requires... Manual Labor' to run...
"Manual" one of the most feared words in today's entitlement world.
-
- Advanced Levergunner
- Posts: 4296
- Joined: Wed Sep 15, 2010 12:57 pm
- Location: Vinita, I.T.
Re: Vintage Buck Saw Question.
I really appreciate and admire the saw, just glad I don't have to use it to cut my fire wood.
M. M. Wright, Sheriff, Green county Arkansas (1860)
Currently living my eternal life.
NRA Life
SASS
ITSASS
Currently living my eternal life.
NRA Life
SASS
ITSASS
Re: Vintage Buck Saw Question.
Nice saw. I have one just like it. The guy I bought my house from left it and some other cool stuff because he didn't want to mess with the stuff....
Nice fix. Looks original to me!
Bob
Nice fix. Looks original to me!
Bob
"Onward thru the Fog"
Re: Vintage Buck Saw Question.
No, it's a cordless.Griff wrote:But... but... it requires... Manual Labor' to run...
Re: Vintage Buck Saw Question.
I took a photo of the saw. Looks pretty similar.
"Onward thru the Fog"
Re: Vintage Buck Saw Question.
Sure does.
When I had mine all apart, I gave the wood parts a big drink of
50/50 mix of linseed oil & turpentine. The wood was dry and
very thirsty.
When I had mine all apart, I gave the wood parts a big drink of
50/50 mix of linseed oil & turpentine. The wood was dry and
very thirsty.